Skil 0560 Notice Originale page 7

- the projected points turn more and more into a line as
the rotational speed increases
- repeated pressing of button F decreases the speed in
6 steps to a standstill
- project a horizontal or vertical line/plane
- make measurements using the projected line/plane/
point as reference
- switch off the tool by pressing button B
! do not stare into the laser beam
! do not point the laser beam at persons or animals
! always switch off the tool after use
• Leveling of tool in horizontal position 7
- place the tool in horizontal position (with base-plate G
beneath) on a flat surface or on the tripod
- level the tool by turning adjustment knobs H and J in
such a way that the bubbles in levels K are centered
! check the leveling after each adjustment
• Leveling of tool in vertical position 8
- place the tool in vertical position (with side-plate L
beneath) on a flat surface or on the tripod
- level the tool by turning adjustment knob J in such a
way that the bubble in level M is centered
! check the leveling after each adjustment
• Projecting points 9
For making references on a longer distance
- place the tool on a flat surface or on the tripod
- level the tool in case of horizontal or vertical reference
lines
- switch on the tool
- align the projected laser point with your target point by
turning rotary head E manually
! check the leveling after each adjustment
• Projecting plumb points 0
- place the tool on a flat surface
- level the tool
- switch on the tool
- a plumb point is projected on the ceiling
! check the leveling after each adjustment
• Working with wall-mounted tool !
For work exceeding the extension height of tripods, the
tool can be mounted to the wall as illustrated
! ensure the tool is mounted properly and cannot
fall down
• Laser viewing glasses @
- for improving the view of the laser line
! these glasses will not protect your eyes against
laser radiation
• Mounting of tool on tripod #
- unfold the tripod
- lock the tripod with ring P
- adjust length of 3 legs with clips Q
- adjust length of rod R with handle S
- lock rod R with knob T
- mount tool on tripod as illustrated
- use adapter V for mounting tool in vertical position
• When working with the tripod on uneven surfaces, level
the tripod itself by adjusting leg lengths with clips Q 1
and checking bubble level W 1
• When using the tripod the tool can be used in any
inclined position for projecting lines under any desired
angle
MAINTENANCE / SERVICE
• This tool is not intended for professional use
• Do not expose the tool to continuous vibration or
extremely hot or cold temperatures
• Always store the tool indoors in its protective bag
• Always keep the tool free of dust, moisture and direct
sunlight
• Clean the tool with a damp cloth and mild soap
! always remove the batteries before cleaning the
lens
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com)
ENVIRONmENT
• Do not dispose of electric tools, batteries,
accessories and packaging together with household
waste material (only for EU countries)
- in observance of European Directive 2012/19/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 4 will remind you of this when the need for
disposing occurs
Laser rotatif
INTRODUCTION
• Cet outil sert à la projection et au contrôle des plans
horizontaux et verticaux, ainsi que des points
(perpendiculaires) de projection
• Cet outil n'est conçu pour un usage professionnel
• Conservez ces instructions dans un lieu sûr et
remettez-les à tout nouvel utilisateur de l'appareil
de mesure
CARACTERISTIQUES TECHNIQUES
Type de laser
Classe laser
Alimentation
Température de fonctionnement
Température de stockage
Poids
Exactitude
ELEMENTS DE L'OUTIL 1
A Couvercle du compartiment des piles
B Bouton marche/arrêt
C Voyant DEL
7
0560
635 nm, <2,2 mW
2
2 piles D (LR20) / 1,5 V
-10°C à 40°C
-10°C à +40°C
1,3 kg
± 0,7 mm/m