Télécharger Imprimer la page

Cybex Platinum CLOUD Z i-SIZE Mode D'emploi page 10

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 16
2. Release the ISOFIX-Release buttons (5) to extend the ISOFIX-Locking arms
(6).
EN
The ISOFIX-Release buttons can both be released independently allowing the
��
ISOFIX-Locking arms to be adjusted independently.
3. Push the ISOFIX-Locking arms (6) out of the base to their furthest extent.
4. Place the base (2) on an appropriate seat in the vehicle.
5. Push the ISOFIX-Locking arms (6) into the ISOFIX-Anchorage points (7) until
these lock into place with an audible "CLICK". The two ISOFIX-Indicators (8)
will switch from RED to GREEN.
6. Ensure the base is secure by trying to pull it out of the ISOFIX-Anchorage
points (7).
7. Push the Base (2) towards the backrest of the vehicle seat until it is fully
aligned with the backrest.
Moving the base from side to side will also brace it against the vehicle
��
backrest.
8. Press the Load leg adjustment button (9) and extend the leg until it touches
the vehicle floor.
9. Pull the Load leg (3) out to the next locking position to ensure optimal force
transmission.
10. The Load leg indicator (10) switches to GREEN when the load leg is correctly
positioned on the vehicle floor. When using the Base Z, the acoustic warning
signal will also stop.
11. Move the Carrying handle (11) to position A. Therefor, press the two Carrying
Handle release buttons on the left and right of the Carrying handle (12) at the
same time.
12. Place the car seat on the Base (2).
13. When used with Base Z, the car seat can also be locked in its entry position
on the base. Then turn the car seat until it is aligned opposite to the direction
of travel.
14. Please ensure that the car seat locks into place with an audible "CLICK".
15. Check whether the Seat locking indicator (13) on the base is GREEN.
16. In order to achieve the best possible protection, activate the Linear side
impact protection (L.S.P) (14) on the side of the car seat facing the vehicle
door by pulling on it's end.
The car seat can also be used with the L.S.P. folded in if there is not enough
��
space in the vehicle. To do this, fold in the element back to its starting position.
8
Installing the car seat with 3-point automatic belt
1. Place the car seat on the vehicle seat against the direction of travel.
2. Make sure that the Carrying handle (11) is locked in position A.
3. Make sure that the Level angle indicator (15) is parallel with the vehicle floor.
4. Pull out the 3-point automatic belt (16) and place its lap section into the lap
belt guide (17).
5. Lock the 3-point automatic belt (16) of the vehicle in its belt buckle.
6. Tighten the lap section by pulling the diagonal section in the direction of travel.
7. Guide the diagonal section of the belt behind the head end of the car seat
and through the diagonal belt guide (18) and above the Linear side-impact
protection (L.S.P) (14).
8. In order to achieve the best possible protection, activate the Linear side
impact protection (L.S.P) (14) on the side of the car seat facing the vehicle
door by pulling on its end.
The car seat can also be used with the L.S.P. folded in if there is not enough
��
space in the vehicle. To do this, fold in the element back to its starting position.
REMOVAL FROM THE VEHICLE
Removal of the car seat with base
1. To unlock the car seat from the base, push the Green seat release button (19)
and pull the Upper seat release button (20) up at the same time.
2. Tilt the car seat slightly and lift it off the base.
3. Unlock the ISOFIX-Locking arms (6) on both sides by pressing the ISOFIX-
Release buttons (5) and at the same time pulling them back.
4. Pull out the Base (2) from the ISOFIX-Anchorage points (7).
5. Remove the Base (2) and slide the ISOFIX-Locking arms (6) completely back
into their transport positions.
6. Push the Load leg (3) back into its original position and then fold it in to
save space.
7. If you are using the Base Z, it is important to fully fold in the load leg so that
the acoustic warning is muted. There is a Load leg parking position (21)
indicated on the underside of the base.
Removal of the car seat with 3-point automatic belt
1. Take the diagonal section of the belt out of the diagonal belt guide (18).
2. Unlock the vehicle seat belt buckle and take the lap section of the belt out
from the lap belt guides (17).

Publicité

loading