Milwaukee M18 FCVN12 Notice Originale page 8

TECHNICAL DATA
Type
Production code
Battery voltage
Vibrations per minute
Weight according EPTA-Procedure 01/2014 (2.0 Ah ... 12.0 Ah)
Flexible shaft
Vibration head diameter
Protection class
Recommended ambient operating temperature
Recommended battery types
Recommended charger
Noise Information:
Measured values determined according to EN 60745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level / Uncertainty K
Sound power level / Uncertainty K
Wear ear protectors.
Vibration Information:
Total vibration values (vector sum in the three axes)
determined according to EN 60745.
Vibration emission value a / Uncertainty K
h
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized
test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of
exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for diff erent
applications, with diff erent accessories or poorly maintained, the vibration emission may diff er. This may signifi cantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when
it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
WARNING!
Read all safety warnings and all
instructions. Failure to follow the warnings and instructions
may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
CONCRETE VIBRATOR SAFETY WARNINGS
Flexible shafts
Avoid sharp bends of the fl exible shaft during operation,
transport and also storage.
Do not use fl exible shaft to pull the motor.
Do not step on or drive over the fl exible shaft.
Vibrating head
Do not put down the vibrating head until the machine has
come to a complete standstill.
Only run the vibrator head in fresh concrete and not in the air,
it can heat up and be damaged.
Do not touch the vibrating head with your hands or other body
parts while it is in operation.
14
M18 FCVN12 M18 FCVN24
Concrete vibrator Concrete vibrator
4910 50 01 XXXXXX MJJJJ 4910 65 01 XXXXXX MJJJJ
18 V
0-12 500 min -1 0-12 500 min
4,4 ... 5,5 kg 5,9 ... 7,0 kg
1,2 m
25 mm
IP 20
-18...+50 °C
M18B..., M18HB
M12-18..., M1418C6
78,43 dB(A) / 3 dB(A) 78,43 dB(A) / 3 dB(A)
89,43 dB(A) / 3 dB(A) 89,43 dB(A) / 3 dB(A)
6,08 m/s 2 / 1,5 m/s 2 5,96 m/s
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is
recommended, such as dust mask, protective gloves, sturdy
non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust protection
mask.
Contact with concrete, cement or other aggregates can cause
skin irritation. Avoid direct contact with the skin.
Remove the battery pack before starting any work on the
machine.
Do not dispose of used battery packs in the household refuse
or by burning them. Milwaukee Distributors off er to retrieve
old batteries to protect our environment.
Do not store the battery pack together with metal objects
(short circuit risk).
Use only System M18 chargers for charging System M18
battery packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only
in dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme
load or extreme temperatures. In case of contact with battery
acid wash it off immediately with soap and water. In case
of eye contact rinse thoroughly for at least 10 minutes and
immediately seek medical attention.
Warning! To reduce the risk of fi re, personal injury, and
ENGLISH
product damage due to a short circuit, never immerse your
tool, battery pack or charger in fl uid or allow a fl uid to fl ow
inside them. Corrosive or conductive fl uids, such as seawater,
certain industrial chemicals, and bleach or bleach containing
18 V products, etc., can cause a short circuit.
-1
SPECIFIED CONDITIONS OF USE
2,4 m
The concrate vibrator is designed for compacting fresh concrete.
25 mm
The vibrating head must be immersed in the fresh concrete.
IP 20
The machine may only be operated if all the instructions in this
operating manual and the service and maintenance instructions are
observed.
No non-permitted components may be connected to the drive.
The machine must not be operated without a fl exible shaft and
vibrating body.
Do not use this product in any other way as stated for normal use.
RESIDUAL RISK
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use and the
operator should pay special attention to avoid the following:
2 / 1,5 m/s 2
• Injury caused by vibration.
Hold the product by designated handles and restrict
working time and exposure.
• Exposure to noise can cause hearing injury.
Wear ear protection and limit exposure.
• Injury due to fl ying debris
Wear eye protection, heavy long trousers, gloves and
substancial footwear at all times.
• Inhalation of toxic dusts.
NOTES FOR LI-ION BATTERIES
Use of Li-Ion batteries
Battery packs which have not been used for some time
should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the
performance of the battery pack. Avoid extended exposure to
heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept
clean.
For an optimum life-time, the battery packs have to be fully
charged, after used.
To obtain the longest possible battery life remove the battery
pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C
and away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
Battery protection for Li-Ion Akkus
In extremely high torque, binding, stalling and short circuit
situations that cause high current draw, the tool will vibrate for
about 5 seconds, the fuel gauge will fl ash,and then the tool
will turn OFF. To reset, release the trigger.
Under extreme circumstances, the internal temperature of the
battery pack could raise too much. If this happens, the fuel
gauge will fl ash until the battery pack cooled down. After the
lights go off , the work may continue.
Transport of Lithium Batteries
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in
accordance with local, national and international provisions
and regulations.
• The user can transport the batteries by road without further
requirements.
• Commercial transport of Lithium-Ion batteries by third par-
ties is subject to Dangerous Goods regulations. Transport
preparation and transport are exclusively to be carried out
by appropriately trained persons and the process has to be
accompanied by corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and
insulated to prevent short circuit.
• Ensure that battery pack is secured against movement
within packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice.
CLEANING
After each use, clean the concrete vibrator from concrete
residues with a damp cloth. Do not clean with a water jet or
high pressure cleaner.
Clean the fl exible shaft and the vibrating haed from concrete
residue with running water after each use.
MAINTENANCE
Visual inspection of all parts for damage.
Battery - visual check for damage.
Battery charger - visual check for
damage.
Check that the connections are tight:
Flexible shaft - vibrator head: tighten if
necessary.
Flexible shaft - drive: if necessary,
securely engage
Clean the machine.
Clean the battery.
Use only Milwaukee accessories and Milwaukee spare parts.
Should components need to be replaced which have not
been described, please contact one of our Milwaukee service
agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the machine type printed as well as the six-
digit No. on the label and order the drawing at your local
service agents or directly at: Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.
ENGLISH
daily after
before operation
x
x
x
x
x
x
15