Harken UNIT 1 Manuel D'instructions page 26

Preassembly
■ If your pin-to-pin headstay length is one of the dimensions shown below, no special length top foil is needed.
A full length 7' (2.13 m) foil is used as the top foil.
24' 8" (7.518 m)
■ You will use a recessed top connector (page 16).
■ If your pin-to-pin headstay length is shown below, use a hacksaw to cut a special
length top foil from a 7' (2.13 m) foil.
24' 9" (7.543 m)
24'10" (7.569 m)
24'11" (7.595 m)
25' 0" (7.620 m)
25' 1" (7.645 m)
■ You will not use a recessed top connector (Page 16).
■ If your pin-to-pin headstay length is shown below use a hacksaw to cut a special
length top foil from a 7' (2.13 m) foil.
25' 2" (7.671 m)
25' 3" (7.696 m)
25' 4" (7.722 m)
■ You will not use a recessed top connector (Page 16). ■ Do not cut 24" (610 mm) bottom foil.
■ If your pin-to-pin headstay length is shown below use a hacksaw to cut a special
-length top foil from a 7' (2.13 m) foil.
25' 5" (7.747 m)
25' 6" (7. 772 m)
25' 7" (7.798 m)
25' 8" (7.823 m)
■ You will use a recessed top connector (page 16).
January 1999
31' 8" (9.652 m)
31' 9" (9.677 m) 38' 9" (11.811 m)
31'10" (9.703 m) 38'10" (11.836 m)
31'11" (9.728 m) 38'11" (11.862 m)
32' 0" (9.754 m) 39' 0" (11.887 m)
32' 1" (9.779 m) 39' 1" (11.913 m)
32' 2" (9.804 m) 39' 2" (11.938 m)
32' 3" (9.830 m) 39' 3" (11.963 m)
32' 4" (9.855 m) 39' 4" (11.989 m)
32' 5" (9.881 m) 39' 5" (12.014 m)
32' 6" (9.906 m) 39' 6" (12.040 m)
32' 7" (9.931 m) 39' 7" (12.065 m)
32' 8" (9.957 m) 39' 8" (12.090 m)
38' 8" (11.786 m)
■ Do not cut 24" (610 mm) bottom foil.
45' 9" (13.945 m)
45'10" ( 13.970 m)
45'11" (13.995 m)
46' 0" ( 14.021 m)
46' 1" ( 14.046 m)
■ Shorten the bottom foil 5
-holes as described on P. 12.
46' 2" (14.072 m)
46' 3" (14. 097 m)
46' 4" (14.122 m)
46' 5" (14.148 m)
46' 6" (14.173 m)
46' 7" (14.199 m)
46' 8" (14.224 m)
■ Shorten the bottom foil 5
-holes as described on P. 12.
Unit 1 MKIII
Foil Length Instruction
45' 8" (13.919 m)
Cut Top Foil to This Length
6 / " (165 mm)
1
2
7 / " (191 mm)
1
2
8 / " (216 mm)
1
2
9 / " (241 mm)
1
2
10 / " (267 mm)
1
2
/ " (140 mm) and drill screw
1
2
Cut Top Foil to This Length
6" (152 mm)
7" (178 mm)
8" (203 mm)
Cut Top Foil to This Length
14 / " (368 mm)
1
2
15 / " (394 mm)
1
2
16 / " (419 mm)
1
2
17 / " (445 mm)
1
2
/ " (140 mm) and drill screw
1
2
13