Publicité
Les langues disponibles
Les langues disponibles
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
•
This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Attaching Side Handle (Fig. B)
WARNING: Before using the tool, check that the handle is
tightened securely.
WARNING: The side handle should always be used to
maintain control of the tool at all times.
Screw the side handle
4
tightly into one of the holes
either side of the gear case.
Mounting and Removing the Guard (Fig. C)
CAUTION: Guards must be used with this grinder.
To Mount the Guard
1. Place the angle grinder on a table, spindle up.
2. Press the guard
3
down (Fig. C1).
3. Position the guard between your body and work piece.
4. Tight the screw
holding the cinch collar firmly around
12
the neck of spindle (Fig. C2)
To Remove the Guard
1. Loosen the screw
12
holding the cinch collar around the
neck of the spindle.
2. Lift up on the guard.
Fitting and Removing a Grinding Disc
(Fig. A, D, E)
WARNING: Do not use a damaged disc.
1. Place the tool on a table, guard up.
2. Fit the backing flange
correctly onto the spindle
7
(Fig. D).
3. Place the disc
9
on the flange
raised centre, make sure that the raised centre
the flange
.
7
4. Screw the outer flange
11
ring on the flange
11
must face towards the disc when
fitting a grinding disc.
5. Press the spindle lock button
until it locks in position.
6. Tighten the flange
11
with the provided spanner.
6
on
8
7
. When fitting a disc with a
10
is facing
onto the spindle
8
(Fig. E). The
2
and rotate the spindle
8
7. Release the spindle lock.
8. To remove the disc, loosen the flange
provided spanner.
Prior to Operation
•
Install the guard and appropriate disc or wheel. Do not use
excessively worn discs or wheels.
•
Be sure the inner and outer flange are mounted correctly.
•
Make sure the disc or wheel rotates in the direction of the
arrows on the accessory and the tool.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
WARNING:
•
Ensure all materials to be ground or cut are secured
in place.
•
Apply only a gentle pressure to the tool. Do not exert
side pressure on the disc.
•
Avoid overloading. Should the tool become hot, let it
run a few minutes under no load condition.
Proper Hand Position (Fig. A, F)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the side handle
with the other hand on the body of the tool, as shown in
Figure F.
Switches
WARNING: Do not switch the tool on or off when
under load.
WARNING: Before using the tool, check that the handle is
tightened securely.
Slider Switch (Fig. A)
DW802/DWE4010/DWE4114/DWE4115
To start the tool, slide the on/off slider switch
the front of the tool. To stop the tool, release the on/off
slider switch.
For continuous operation, slide the switch toward the front of
the tool and press the forward part of the switch inward.
To stop the tool while operating in continuous mode, press the
rear part of the slider switch and release.
English
11
with the
,
4
1
toward
7
Publicité
