Whirlpool CHW9150 Guide De Dépannage page 2

FOR SERVICE TECHNICIAN ONLY - DO NOT REMOVE OR DESTROY
CONTROL SET-UP PROCEDURES
IMPORTANT: Read all instructions before operating.
9150 Models: Insert access door key, turn, and lift
n
to remove access door.
9160 Models: Once the debit card reader is installed (according
n
to the reader manufacturer's instructions), the set-up mode can
only be entered by inserting a set-up card (supplied by the reader
manufacturer) into the card slot. If a set-up card is not available,
diagnostic modes can be entered by removing connector AA1
on the circuit board or by using the Service Access Code (see
Service Access Code section, page 9) for 9160 models.
IMPORTANT: Unplug washer or disconnect power before opening
the console. To access connector AA1:
1. Unplug washer or disconnect power.
2. Open console, disconnect plug on AA1, close console.
3. Plug in washer or reconnect power.
The washer is now in the set-up mode. The lower three buttons and
the digital display are used to set up the controls. The display can
contain 4 numbers and/or letters and a decimal point. These are
used to indicate the set-up codes and related code values available
for use in programming the washer.
Once the washer has been programmed with a Gen. 2 card reader
installed, the washer will be in dAS mode permanently, and dAS will
be displayed every time set-up mode is accessed.
How to use the buttons to program the controls
1. The HOT button is used to adjust the values associated with set-
up codes. Pressing the button will change the value by increments.
Rapid adjustment is possible by holding the button down.
2. The WARM button will advance through the set-up codes.
Pressing this button will advance to the next available set-up
code. Holding the button down will automatically advance
through the set-up codes at a rate faster than one (1) per second.
3. The COLD button is used to select or deselect options.
Start Operating Set-Up
Before proceeding, it is worth noting that, despite all of the options
available, an owner can simply choose to uncrate a new commercial
washer, hook it up, plug it in, and have a washer that operates.
Washers are preset at the factory for an 11-minute wash period
and three rinses (no extra rinse).
SET-UP CODES
The WARM button will advance from code to code.
n
The HOT button will change the code value.
n
The COLD button will select or deselect options.
n
NOTE: The set-up codes are the same for all models except
where noted.
The set-up code is indicated by the one or two left-hand
characters. The set-up code value is indicated by the two or three
right-hand characters.
NOTE: The first line of each code indicates the factory default
for 9150 models.
2
CODE
608 REGULAR CYCLE PRICE
608
When the d.xx is set to d.00, this 6 xx value represents the number
of coins (coin 1) needed to start the washer; may adjust from 0-39.
Change this value by pressing the HOT button. 6 08 = 8 quarters =
$2.00. 9160 models default to 6 00. NOTE: When coin slide mode is
deselected, set 'b.xx' equal to value of one coin in nickels. b.05 = $0.25.
601
When the d.xx is set to d.CS, this 6 xx value represents the
number of push-in actuations of the coin slide to start the washer.
6 01 would equal one coin slide activation.
g
Press the WARM button once to advance to next code.
711 WASH LENGTH
711
This is the number of minutes for WASH. Washer comes from the
factory preset with 11 minutes. Choose from 9-17 minutes by
pressing the HOT button.
g
Press the WARM button once to advance to next code.
800 ADDITIONAL RINSE OPTION
This option is either SELECTED 'ON' or NOT SELECTED 'OFF'.
800 Not Selected 'OFF'.
8Ar Selected 'ON'.
Press the COLD button once for this selection.
g
Press the WARM button once to advance to next code.
900 CYCLE COUNTER OPTION
This option is either SELECTED 'ON' or NOT SELECTED 'OFF'.
900
Not Selected 'OFF'.
90C
Selected 'ON' and not able to be deselected.
Press the COLD button 3 consecutive times to select 'ON'.
Once selected 'ON' it cannot be deselected.
g
Press the WARM button once to advance to next code.
MONEY COUNTER OPTION
1.00
This option is either SELECTED 'ON' or NOT SELECTED 'OFF'.
1.00 Not Selected 'OFF'.
1.0C Selected 'ON'.
Press the COLD button 3 consecutive times to select 'ON' and 3
consecutive times to deselect (Not Selected 'OFF'.) Counter resets
by going from 'OFF' to 'ON'.
g
Press the WARM button once to advance to next code.
1.C0
Selected 'ON' and not able to be deselected.
To select 'ON' and not able to be deselected, first select 'ON',
then within 2 seconds press the COLD button twice, the HOT
button once, and exit the set-up mode.
g
Press the WARM button once to advance to next code.
2.00 SPECIAL PRICING OPTION
This option is either SELECTED 'ON' or NOT SELECTED 'OFF'.
2.00 Not Selected 'OFF', and next available code will be A.00.
2.SP Selected 'ON'. Press the COLD button once for this selection.
If SPECIAL PRICING OPTION is selected, you have access to codes '3.XX'
through '9.XX'.
g
Press the WARM button once to advance to next code.
OPTIONS TO USE IF SPECIAL PRICING IS SELECTED:
3.08 SPECIAL CYCLE PRICE
3.08 Represents the number of quarters (coin 1) to start a cycle:
may adjust from 0-39. (See VALUE OF COIN 1.) Advance
from 0-39 by pressing the HOT button. Factory default
of 8 quarters = $2.00.
3.00 9160 MODELS ONLY: Factory default of 0 quarters.
g
Press the WARM button once to advance to next code.
EXPLANATION