Assembly; Enclosed Tools; Assembling The Base (01 - 04); Installing The Axle And Wheels (05 - 08) - AL-KO solo TCS Duotec 2500 Mode D'emploi

Assembly

from the mains connection prior to moving
the machine.
■
When moving the shredder, only transport it
using its handle.
■
Always ensure a stable stance when working.
Do not bend forward too far.
■
Do not feed the shredder from an elevated
position.
■
Always disconnect the shredder from the
mains power supply when not in use.
In the event of a malfunction or accident:
■
Immediately disconnect the mains plug from
the mains if the mains cable has been dam-
aged or severed!
■
If a foreign object is drawn in or in the event
of unusual noises or vibrations, immediately
switch off the shredder and disconnect it from
the mains. Then proceed as follows:
■
Inspect the damage.
■
Refasten loose parts, e.g. tighten screws.
■
Have all damaged parts exchanged or re-
paired by our customer service.
5 ASSEMBLY
WARNING! Danger if assembly is not
carried out completely! Use of an incompletely
assembled device can result in serious injury.
■
Only use the device when it is fully assem-
bled!
■
Before switching on, check that all safety and
protective devices are in place and function-
ing correctly!
5.1

Enclosed tools

■
1 socket wrench WAF 10
■
1 open-end/ring spanner WAF 10/8
■
1 Torx bit T30
5.2 Assembling the base (01 – 04)
Accessories:
■
2 base tubes
■
6 bolts M8 x 35/40 (TCS Duotec 2500: one of
which is already mounted on the appliance)
■
6 washers 8.4 x 16 - DIN 125
■
6 hexagon nuts M8
■
2 washers 10.5 x 30 x 5
1. Place the appliance on a suitable surface,
e.g. a table.
2. Divide the shredder centrally.
456251_g
3. Unscrew the nut M8 (01/1).
4. Pull out (01/b) the pull rod (01/2) and remove
the upper section.
5. Release the securing bolt (02/1).
6. Turn the central lock (02/2) and fold the feed
tube away.
7. Fold the lower section away sideways and re-
move the cardboard.
8. Position the washers 10.5 x 30 x 5 and base
tube on the housing and insert the screws M8
x 35/40 (3).
9. Fix the base tube in position with the washers
8.4 x 16 (DIN 125) and nuts M8. (Assembly is
identical on the left and right) (4).
NOTE To simplify axle installation, do not
tighten the nuts completely but only fix the base
tubes in position using bolts.
5.3 Installing the axle and wheels (05 – 08)
Accessories:
■
1 axle tube
■
2 bolts M8x40
■
2 washers diam. 8.4x16 - DIN 125
■
2 nuts M8
■
2 wheels with ball bearings
■
2 collar bolt (=axles)
■
2 hexagon nuts M10
■
2 corrugated washers 13x24x0.5
■
2 lock washers 10.5
1. Bolt (05) the axle tube to the feet using 2
bolts M8x40, 2 washers diam. 8.4x16 and 2
hexagon nuts M8.
2. Tighten the 6 nuts on the base tubes.
3. Place the shredder lower section onto the
feet.
4. Place the shredder upper section onto the
shredder lower section (06).
5. Engage the shredder upper section in the
central lock.
6. Insert the pull rod through the holes in the
shredder upper section and lower section
(07).
7. Screw a nut M8 onto the pull rod (07).
8. Screw in the securing bolt (02/1).
9. Fasten the wheels (with pressed-in ball bear-
ings) to the axle tube with a collar bolt, 2 cor-
rugated washers 13x24x0.5, 2 serrated
washers 10.5 and a nut M10 (08).
10. Mount the wheel covers on the wheels (08).
19