Assembly; Electrical Connection - Scheppach HD2P Traduction Des Instructions D'origine

8. Assembly

m ATTENTION!
Always make sure the device is fully assembled
before commissioning!
Ensure that the machine is standing on level and firm
ground.
Inserting/replacing the dust bag, fig. 2/3
• Open both clamps (3) and fold the case cov-
er backwards. Open the lid for the dust bag (10),
press the clamping bracket (12) on the dust bag
and push it over the suction nozzle.
• Close the lid again until it clicks into place. When
you empty a full dust bag, clean the dust bag
chamber with a moist cloth or brush before you in-
serting it again.
• Pass the connection cable through the notch (a) on
the front. Close the case cover and lock it with both
clamps.
Suction function, fig. 4-7
• Remove the power plug for all conversions.
• When using the suction function, always insert a
dust bag. The connection nozzle (14) must be in-
serted on the side of the dust bag. (16) Insert the
suction grating with filter on the opposite side.
Make sure both parts click into place. Insert the
suction hose (6) with the lug into the connection
nozzle (14) and lock in it place by rotating it slightly.
• Attach a jet nozzle onto the suction hose; connect
the mains plug and press the on button.
Function: Blowing out, off and up, fig. 4-7
• The conversion of the device for blowing out can
be done in a few simple steps.
• Remove the connection nozzle (14) from the suc-
tion side and insert on the opposite side. (17)
• Insert suction grating with filter on the suction side.
Connect the suction hose and attach the blowing
nozzle (7).
• Keeping the hole on the jet nozzle closed will in-
crease the blowing pressure.
• Do not point the air flow at persons or animals.
Working instructions
Prior to every start-up of the machine, inspect the
equipment for proper function.
Notes on the use of borehole-suction nozzle, fig. 8
• Attach the drill suction nozzle (9) to the suction
hose.
• Switch on the suction device and place the drill
suction nozzle onto the borehole.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
• Due to the vacuum, the nozzle sticks to level sur-
faces.
Use of the inflation nozzle, fig. 9-10
• The suction-blowing nozzle (7) can be used for
suction or inflating of suitable objects. Set the suc-
tion device to blowing mode.
• Place the suction-blowing nozzle onto the suction
hose.
• Switch the suction device on.
• By covering the borehole (a) on the nozzle, you
can regulate the airflow

9. Electrical connection

The electrical motor installed is connected and
ready for operation. The connection complies
with the applicable VDE and DIN provisions.
The customer's mains connection as well as
the extension cable used must also comply with
these regulations.
Damaged electrical connection cable
The insulation on electrical connection cables is of-
ten damaged.
This may have the following causes:
• Passage points, where connection cables are
passed through windows or doors.
• Kinks where the connection cable has been im-
properly fastened or routed.
• Places where the connection cables have been cut
due to being driven over.
• Insulation damage due to being ripped out of the
wall outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not
be used and are life-threatening due to the insula-
tion damage.
Check the electrical connection cables for damage
regularly. Make sure that the connection cable does
not hang on the power network during the inspection.
Electrical connection cables must comply with the
applicable VDE and DIN provisions. Only use con-
nection cables with the marking „H05VV-F".
The printing of the type designation on the connec-
tion cable is mandatory.
AC motor
• The mains voltage must be 230 V~
• Extension cables up to 25 m long must have a
cross-section of 1.5 mm .
2
Connections and repairs of electrical equipment may
only be carried out by an electrician.
Please provide the following information in the event
of any enquiries:
• Type of current for the motor
• Machine data - type plate
• Motor data - type plate
GB | 17