Rupes LE71T Сonversion Des Instructions De Fonctionnement Original page 10

Mod. 9.2482_03-2017_Layout 1 23/03/17 14.17 Pagina 10
The conformation of the accessories must be correctly adapted to the spindle
of the tool. The accessories equipped with holes of the shaft that do not
correspond to the assembly components on the tool, will not remain in
balance, they will vibrate excessively and can cause a loss of control.
Do not use a damaged accessory. If the tool or accessory has suffered a fall,
examine any damages or install an accessory that is no damaged. After
examining and installing an accessory, all persons present, must keep a safe
distance from the rotating accessory and operate the tool at maximum empty
speed for one minute. Damaged accessories generally break during this test
period.
Use the electric tool only for dry sanding. The use of water or other liquid
coolants can cause electrocution or an electric shock.
Do not operate the electrical tool in the proximity of flammable material. The
sparks generated by sanding metal material can ignite these materials.
Avoid overheating the material being processed and in sanding.
Before taking a break, always empty the container of dust. Abrasive dust in
the filter holder or in the vacuum filter can catch fire in unfavourable conditions
such as a spark produced during metal sanding. Hazardous dust can be produced
during sanding operations, contact with which or inhalation can pose a danger for
the user's health and for people nearby. Comply with the valid safety specifications
in the respective countries.
Connect the tool to a device suitable dust extraction. To protect the health wear
masks.
Use clamps to secure the work piece. Under no circumstances should you
hold the work piece with one hand and the electrical tool with the other hand,
while it is being used. By securing the work piece with clamps, you can have
both hands free to better operate the electrical tool.
INFORMATOIN NOISE / MEAN ACCELERATION VALUE
The tools are suppressed in accordance for the prevention and elimination of radio
disturbances measured in accordance with standard: EN 60745
Sound pressure level / Sound power level
L PA L WA
dB(A)
LE71T 74 85
LE71TE 74 85
LS71T 74 85
LS71TE 74 85
LR71TE 74 85
LE71TC 74 85
LE71TEC 74 85
LC71T 74 85
LC71TE 74 85
10
3 axis vibration level
a h
Uncertainty Uncertainty
m/s 2
3 3,00 1,50
3 3,00 1,50
3 3,00 1,50
3 3,00 1,50
3 3,00 1,50
3 3,50 1,55
3 3,50 1,55
3 3,50 1,55
3 3,50 1,55
DANGER The indicate measurements refer to new power tools.
Daily usa causes the noise and vibration values to change.
Displayed emission values are comparative and are to be employed for a
provisional assessment of the operator's risk exposure during the work period.
Appropriate evaluation of work period must also include tool's idle and stop
periods. These emission values represent the tool's main applications.
If the tool is used for other applications, with other accessories, or if it does not
undergo regular maintenance, emission values can significantly increase
during operations.
Use hearing protection!
PARTS OF ThE TOOL
1 - Technical data identification label
2 - ON/OFF switch
3 - Speed control (LE71TE-LS71TE-LR71TE-LE71TEC-LC71TE)
4 - 29 mm Ø suction port
5 - Velcro pad holder:
5a - Rectangular (LE71T-LE71TE)
5b - Triangular (LS71T-LS71TE)
5c - Circular (LR71TE)
5d - Rectangular Clip (LE71TC-LE71TEC)
5e - Rectangular 80x197,5 (LC71T-LC71TE)
6 - Motor ventilation slots
7 - Pad fixing screws
8 - Conical filter:
8a - Filter holder
8b - Cartridge
STARTING UP
wARNING
Pay attention to the mains voltage! The mains voltage must
correspond to the voltage indicated on the technical data identification
place (1).
DANGER
Before any intervention on the electrical tool take the plug out
from the socket
bEFORE STARTING ThE TOOL
Before starting-up the tool, ensure that:
- the packaging is complete and does not show signs of having been damaged
during storage or transport;
- the tool is complete; check that the number and type of components comply
with that reported in this instruction booklet;