Makita DCO140 Manuel D'instructions page 5

ENGLISH
(Original instructions)
1 Red indicator
2 Button
3 Battery cartridge
4 Star marking
5 Thumb screw
6 Shoe
7 Slide switch
8 Collet nut
9 Shaft lock
SPECIFICATIONS
Model
Collet chuck capacity
Rated speed (n)/ No load speed (n
Overall length
Net weight
Rated voltage
• Due to our continuing program of research and
development, the specifications herein are subject to
change without notice.
• Specifications and battery cartridge may differ from
country to country.
• Weight, with battery cartridge, according to EPTA-
Procedure 01/2003
Intended use
The tool is intended for cutting gypsum, wood, plastic
and soft wall tiles.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future
reference.
CORDLESS CUT-OUT TOOL SAFETY
WARNINGS
1. Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
2. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by your hand or against the body
leaves it unstable and may lead to loss of control.
3. Wear eye protection and dust mask.
4. Ventilate your work area adequately.
5. Check the bit carefully for cracks or damage
before operation. Replace cracked or damaged
bit immediately.
Explanation of general view
10 Tighten
11 Loosen
12 Collet cone
13 Bit
14 Projections
15 Circular guide
16 Knob
17 Vacuum cover
18 Tool
DCO140
3 mm, 6 mm or 1/8", 1/4"
) 30,000 min
0
313 mm
1.6 kg
D.C. 14.4 V
6.
7.
ENE012-1
8.
GEA010-1
9.
10. Make sure that the shaft lock is released before
11. Always use with the shoe securely attached to
12. Hold the tool firmly.
13. Do not perform any operation using your hands
GEB123-1
14. Keep hands away from moving parts.
15. Do not use this tool for drilling.
16. Do not leave the tool running. Operate the tool
17. Always switch off and wait for the bit to come to
18. Do
19. Draw attention to the need to use cutters of the
SAVE THESE INSTRUCTIONS.
19 Hose 28
20 Hose for vacuum cleaner
21 Vacuum cleaner
22 Dust collector
23 Limit mark
24 Holder cap cover
25 Screwdriver
26 Brush holder cap
3 mm, 6 mm or 1/8", 1/4"
–1
Check for the proper clearance beneath the
workpiece before cutting so that the bit will not
strike a hard surface such as the floor,
workbench, etc.
Do not cut metal objects such as nails and
screws. Inspect for and remove all nails, screws
and other foreign material from the workpiece
before operation.
Check that the bit is not contacting the
workpiece before the switch is turned on.
Always hold the tool with two hands while
switching the tool on. The motor torque can
cause the tool to turn.
Before using the tool on an actual workpiece, let
it run for a while. Watch for vibration or wobbling
that could indicate improperly installed bit.
the switch is turned on.
the tool and positioned flat and firmly against
the workpiece.
to support or guide the workpiece.
only when hand-held.
a complete stop before removing the bit from
workpiece.
not touch the
immediately after operation; they may be
extremely hot and could burn your skin.
correct shank diameter and which are suitable
for the speed of the tool.
DCO180
–1
30,000 min
313 mm
1.7 kg
D.C. 18 V
bit or the workpiece
5