Skil 1012 Notice Originale page 9

6 Automatic shut-off when charger gets too hot (thermic
fuse blows and charger becomes useless)
7 Incorrect polarity of the charger connection could cause
a hazard (only charge the battery with the charger
supplied)
8 Insulation class III
9 IP20 (degree of protection against dust and humidity)
q Do not dispose of the charger together with household
waste material
w Do not dispose of the battery together with household
waste material
USE
• Charging battery e
- battery of new tools is not fully charged
! unplug the charger from the tool after charging
period has ended thereby lengthening the service
life of the battery
IMPORTANT:
- while charging, the charger and the battery may
become warm to touch; this is normal and does not
indicate a problem
- do not charge at temperatures below 0°C and over
45°C; this will seriously damage the battery as well as
the charger
! a battery that is new or has not been used for a
longer period does not develop its full capacity
until after approximately 5 charging/discharging
cycles
- connect charger B with both wall socket and contact C
- charging light D turns on indicating that the tool is
being charged
- charge the battery for at least 5 hours, after which the
battery may be used (red light D will stay on)
- do not repeatedly recharge the battery after only a few
minutes of operation; this may result in a reduction of
operating time and battery efficiency
- the battery must be kept separate from the natural
environment and should not be disposed of as normal
domestic waste (symbol w will remind you of this
when the need for disposing occurs)
- if you anticipate long periods of non-use for the tool, it
is best to unplug the charger from its power source
On/off r
•
• Changing direction of rotation t
- when not properly set in left/right position, switch A 2
cannot be activated
! change direction of rotation only when tool is at a
complete standstill
• Changing bits y
! do not use 25 mm bits without magnetic bitholder
E 2
! do not use bits with a damaged shank
• Automatic spindle-lock
Allows you to manually tighten or loosen screws, when
necessary u
• Spot light i
Spot light F automatically lights on when activating
switch A, even when switch G is in the middle (locking)
position
• Torch o
Switch on/off torch H by pushing switch J in "I"/"O"
position
• Two handle positions p
APPLICATION ADVICE
• Use the appropriate bits a
! do not use damaged bits
! only use bits with hexagon shaft
• When turning in a screw at/near the cross cut end or an
edge of wood, pre-drill a hole in order to avoid cracking
of the wood
• For an optimal use of the tool a steady pressure on the
screw is required, especially while removing
• When screwdriving in hard wood one should pre-drill a
hole
• For more tips see www.skil.com
MAINTENANCE / SERVICE
• This tool is not intended for professional use
• Keep tool and charger clean
! unplug charger from power source before
cleaning
• If the tool/charger should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool or charger undismantled together with
proof of purchase to your dealer or the nearest SKIL
service station (addresses as well as the service
diagram of the tool are listed on www.skil.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol q will remind you of this when the need for
disposing occurs
! remove the batteries before disposal of the tool
• Removing/disposing of batteries s
! only remove the batteries if they are completely
empty
- protect battery terminals with heavy tape to prevent
short-circuit
- dispose of the batteries at an official collection point
for batteries
! batteries may explode when disposed of in fire,
so do not burn battery for any reason
DECLARATION OF CONFORMITY
• We declare under our sole responsibility that the product
described under "Technical data" is in conformity with
the following standards or standardization documents:
EN 60335, EN 61000, EN 60745, EN 60598, EN 62471,
EN 55014, in accordance with the provisions of the
9