Martin Logan BalancedForce 210 Manuel De L'utilisateur page 5

Safety Warnings and Installation in Brief (English)
WARNING!
• Hazardous voltages exist inside—do not remove cover.
• Refer servicing to a qualified technician.
• To prevent fire or shock hazard, do not expose this
module to moisture.
• Turn amplifier off and unplug subwoofer should any
abnormal conditions occur.
• The power cord should not be installed, removed, or
left detached from the speaker while the other end is
connected to an AC power source.
• The main power switch near the AC inlet shall
remain readily operable.
• Use only with a grounded electrical outlet.
• No candles or other sources of open flame should
be placed on the speaker.
• No liquids either in glasses or vases should be
placed on speaker.
• Speaker should not be exposed to dripping or
splashing liquids.
• The terminals marked with the lightning bolt symbol
should be connected by an instructed person or by
way of ready made terminals.
• The power cord should remain readily operable
should any abnormal conditions occur.
We know you are eager to hear your new MartinLogan subwoofer, so
this section is provided to allow fast and easy set up. Once you have
your subwoofer operational, please take the time to read, in depth, the
rest of the information in the enclosed manual. It will give you perspective
on how to attain the greatest possible performance from this most exacting
woofer system.
If you should experience any difficulties in the setup or operation of your
MartinLogan subwoofer, please refer to the Room Acoustics, Placement
or Operation sections of the enclosed owner's manual. Should you
encounter a persistent problem that cannot be resolved, please contact
your authorized MartinLogan dealer. They will provide you with the
appropriate technical analysis to alleviate the situation.
Step 1: Unpacking
Remove your new subwoofer from its packing. Please retain the original
packing materials for future use—replacement packaging may be expensive.
Step 2: Placement
You may choose to begin by placing the subwoofer in a corner near the
front of the room. If placed in a corner, align the subwoofer diagonally
so both woofers are equidistant from the adjacent wall. Before decid-
ing on a permanent corner placement, experiment with other positions.
Locations away from corners often prove more effective in providing
ideal low-frequency performance and blend with the main speakers.
Please see the Placement section for details.
Step 3: Signal Connection
Use the best cables you can. High quality cables, available from your spe-
cialty dealer, are recommended and will give you superior performance.
Attach your preamplifier/processor outputs to the signal input connec-
tors located on the subwoofer's rear panel. Please see the Controls and
Connections section for details.
If you plan to connect your subwoofer using Speaker Level (high level)
inputs, refer to the Speaker Level Inputs section for details.
Step 4: Power Connection (AC) (see warning)
Make sure the level knob is set at 0. Plug the subwoofer into a wall out-
let. Review the AC Power Connection section of this manual for details.
Step 5: Setting the Controls
• Set the Level knob to 3 or 4.
• Set the Mode switch to 'Auto (Trigger)'.
• Set the 25Hz Level knob to 0.
• Set the Phase knob to 90°.
• Set the Low Pass Filter knob to a setting lower than the low-end fre-
quency response of your main speakers. If you are uncertain of your
main speaker low-frequency response, start with a setting of 35Hz.
Step 6: Listen and Enjoy.
安全警告及安装简介 (中国的 / Chinese)
警告!
• 内部存在危险电压—请勿擅自拆盖。
• 如需服务，请联系有资质的技术人员。
• 为防止火灾或电击危害，请勿将组件暴露于潮湿
环境中。
• 如发生任何反常情况，请立即关闭功放，并拔掉
低音炮插头。
• 当电源线接入交流电源插座时，请勿插拔电源线
与扬声器连接的另一端口，以避免危险发生，和
可能导致的对产品本身带来的损害。
• 靠近电源插座的主电源开关应保持随时可操作状态。
• 仅使用接地的电源插座。
• 请勿将蜡烛或其它明火源置于扬声器上。
• 请勿将含有液体的玻璃容器或花瓶置于扬声器上。
• 请勿使扬声器接触到水滴或飞溅液体。
• 标有闪电符号的端子应由受过培训的专业人员来
连接，或经由现成的端子连接。
• 如发生任何反常情况，电源线应保持随时可操作
状态。
我们深知，您已迫不及待想感受下这款全新的低音炮了。所以我们为
您编写了以下内容，便于您更加简易迅速地进行安装。一旦您着手操
作时，请花点时间仔细阅读本章节，并深入了解随产品附上的用户手
册中的信息。它能教您如何使这款最精确的低音扬声器系统发挥最佳
的性能。
5 5