Télécharger Imprimer la page

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 13

Product Use

Installation Concerns
This enhanced child restraint is suitable for vehicle seats with i-Size ISOFIX
anchor points with the Base. (1)
DO NOT use the rearward facing enhanced child restraint systems in seating
positions where there is an active frontal airbag installed. (2) Death or
serious injury may occur. Please reference vehicle owner's manual for more
information.
DO NOT install this enhanced child restraint on vehicle seats that face
sideways or rearward with respect to the moving direction of the vehicle.
Please refer to your vehicle owner's manual for recommended or suggested
installation positions. (3)
It is recommended to install this enhanced child restraint on the rear vehicle
seat. (4)
DO NOT install this enhanced child restraint on vehicle seats movable during
installation.
Handle Adjustment
1
- The handle of the infant carrier can be adjusted to 2 positions. (5)
Position for car, hand or stroller transportation. (5)-1 Baby chair position.
(5)-2
2
- To adjust the handle, squeeze handle adjustment buttons on both sides
to release it (6)-1, and then rotate the handle until it clicks into any of the
2 positions. (6)-2
Base Installation
1
- Attach the ISOFIX guides to the vehicle's ISOFIX anchor bars (see vehicle
owner's manual). (7) The ISOFIX guides can protect the surface of the
vehicle seat from being torn. They can also guide the ISOFIX connectors.
2
- Unfold the load leg from storage compartment. (8)
3
- Extend the ISOFIX connectors by pressing the ISOFIX adjustment button
while pulling on the connector. (9)
4
- Press the ISOFIX adjustment button to adjust the ISOFIX connectors.
Line up the ISOFIX connectors with the ISOFIX guides, and then click
both ISOFIX connectors into the ISOFIX anchor bars. (10)
9
ARRA next instruction
Make sure that both ISOFIX connectors are securely attached to the
vehicle's ISOFIX anchor bars. There should be two audible clicks and
the colors of the indicators on the both ISOFIX connectors should be
completely green. (10)-1
Check to make sure the base is securely installed by pulling on the both
ISOFIX connectors.
5
- After placing the base on the vehicle seat, extend the load leg to floor
(11). When the load leg is installed correctly, the load leg indicator will
show green. Red will be shown when installed incorrectly. (11)-2
The load leg has multiple positions. When the load leg indicator shows
red this means the load leg is in the wrong position.
Make sure the load leg is in full contact with the vehicle floor pan.
Squeeze the load leg adjustment button, then shorten the load leg
upwards. (11)-1
The completely assembled base is shown as (12).
The ISOFIX connectors must be attached and locked onto the ISOFIX
anchor bars. (12)-1
The load leg must be installed correctly with green indicator. (12)-2
Attaching Infant Carrier to the Base
1
- Push the infant carrier down into the base (13), if the infant carrier is
secure, the shell indicator will show green. (14)
Check that the infant carrier is locked onto the base by pulling up on the
handle.
2
- Press the ISOFIX adjustment button, and push the base back until it
comes in contact with the vehicle seat back. (15)
3
- To release the infant carrier, squeeze the infant carrier release button
(16)-1, then lift the infant carrier up. (16)-2
Uninstalling the Base
1
- To remove the base, press the secondary lock button (17)-1 first, followed
by the button (17)-2 on the ISOFIX connectors before removing the base
from the vehicle seat. (17)
2
- For transporting, press ISOFIX Adjustment button and move back ISOFIX
connectors back into the storage position. (18)
ARRA next instruction
10

Publicité

loading