Publicité
Les langues disponibles
Les langues disponibles
REAR PANEL
CAN-ICES-3(B)/NMB-3(B)
SPEAKER JACKS PARALLELED
FULL
HALF
FULL POWER
4
8
120W RMS/
8
16
44V RMS 4 MIN.
16
32
HALF POWER
IMPEDANCE
OUTPUT
POWER
CLASS 2 WIRING
28
Consumo de energia 300Wh
FUSE
F5AL/250V
Consumo de energia
en modo de espera 92Wh
120V
60 Hz
300 WATTS
(17) MIDI IN/FOOTSWITCH
This 8-pin DIN connector is provided for the connection of the remote footcontroller. See the FOOTSWITCH
section of this manual for a more detailed explanation of operation. This can also be used as a MIDI IN connec-
tion, using a standard 5-pin MIDI cable, if the amp is going to be controlled by a separate MIDI controller other
than the supplied footcontroller. See the MIDI section of this manual for a more detailed explanation of the
MIDI features.
(18) MIDI OUT
This 5-pin DIN connector is provided to send MIDI messages, including Program Change and Continuous Con-
troller messages, to external MIDI devices. It is useful for linking two amps and keeping their functions synchro-
nized, and for sending your custom preset data to another amp or MIDI backup device. It's also useful to control
presets on effects units you may have in the effects loops. See the MIDI section of this manual for a more detailed
explanation of the MIDI features.
(19) 9VDC AUX POWER SUPPLY
These pedal-standard, 9VDC (negative tip) barrel jacks are provided for quick power connection to a variety of
pedals or other peripheral devices. Each jack is capable of providing up to 500mA of current.
(20 and 21) EFFECTS LOOPS
These series loops are used to route the Invective 120 signal path through external effects devices or signal pro-
cessors.
Note: the loops are after the master boost, but before the master volume in the signal path. This allows the master
boost to not boost/cut ambient effects trails.
(22) MASTER BOOST
This control sets the amount of footswitchable post-EQ volume boost available with a range of 0-5dBV.
Note: this control is before the effects loops in the signal path.
6
22
5
4
6
3
7
2
8
4
1
9
3
0
10
2
OUTPUT
5
4
6
1
3
7
0
GROUND
LEVEL
2
8
LIFT
1
9
0
10
27
26
25
CAN-ICES-3(B)/NMB-3(B)
SPEAKER JACKS PARALLELED
FULL
HALF
FULL POWER
4
8
8
16
16
32
HALF POWER
IMPEDANCE
OUTPUT
POWER
21
20
5
6
7
RETURN
RETURN
8
9
WARNING:
APPARATUS SHOULD NOT BE EXPOSED TO RAIN OR MOISTURE AND
10
OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT
BE PLACED ON THIS APPARATUS. TO PREVENT THE RISK OF FIRE
AVIS:
DECHARGE ELECTRIQUE, CET APPAREIL NE DOIT PAS ETRE EXPOSE
A LA PLUIE OU A L 'HUMIDITE ET AUCUN OBJET REMPLI DE LIQUIDE,
SEND
SEND
TEL QU'UN VASE, NE DOIT ETRE POSE SUR CELUI-CI. REMPLACER
24
23
4
3
2
1
120W RMS/
0
44V RMS 4 MIN.
OUTPUT
4
3
GROUND
2
LIFT
1
CLASS 2 WIRING
0
19
A PRODUCT OF PEAVEY
ELECTRONICS CORP.
www.peavey.com
CAUTION
AVIS:
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
9VDC @ 500mA
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, THIS
(NEGATIVE TIP)
POWER
HAZARD, REPLACE WITH SAME TYPE 250 VOLT FUSE.
DANS LE BUT DE REDUIRE LES RISQUES D'INCENDIE OU DE
SUPPLY
PAR UN FUSIBLE DE MEME TYPE ET DE 250 VOLTS.
5
6
7
8
5
4
6
9
3
7
10
RETURN
2
8
5
6
1
9
7
0
10
8
LEVEL
9
SEND
10
18
17
DESIGNED AND
ENGINEERED IN USA
MIDI
MIDI
OUT/
FOOT-
THRU
SWITCH IN
CAUTION
RETURN
AVIS:
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, THIS
APPARATUS SHOULD NOT BE EXPOSED TO RAIN OR MOISTURE AND
OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT
BE PLACED ON THIS APPARATUS. TO PREVENT THE RISK OF FIRE
HAZARD, REPLACE WITH SAME TYPE 250 VOLT FUSE.
AVIS:
DANS LE BUT DE REDUIRE LES RISQUES D'INCENDIE OU DE
DECHARGE ELECTRIQUE, CET APPAREIL NE DOIT PAS ETRE EXPOSE
A LA PLUIE OU A L 'HUMIDITE ET AUCUN OBJET REMPLI DE LIQUIDE,
SEND
TEL QU'UN VASE, NE DOIT ETRE POSE SUR CELUI-CI. REMPLACER
PAR UN FUSIBLE DE MEME TYPE ET DE 250 VOLTS.
A PROD
ELECT
www
9VDC
(NEG
PO
SU
Publicité
