Bosch Professional GKS 18V-57 G Notice Originale page 18

18 | English
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
Do not use HSS saw blades. Such saw blades can easily
u
break.
Do not saw any ferrous metals. Hot chips may ignite the
u
dust extractor.
Wear a dust mask.
u
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Do not open the battery. There is a risk of short-circuit-
u
ing.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery with products from the manufac-
u
turer. This is the only way in which you can protect the
battery against dangerous overload.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for making straight cuts in wood
with and against the grain and mitre cuts in wood while rest-
ing firmly against the workpiece.
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
Technical data
Circular saw
Article number
Rated voltage
No-load speed A)
Max. cutting depth
1 609 92A 7SZ | (18.05.2022)
(1) Lock-off button for on/off switch
(2) Worklight
(3) Hex key
(4) Auxiliary handle (insulated gripping surface)
(5) Spindle lock button
(6) Base plate
(7) Wing bolt for parallel guide
(8) Wing bolt for mitre/bevel angle preselection
(9) Scale for mitre/bevel angles
(10) Cut mark 45° (0° on GKS 18V-57 G)
(11) Cut mark 0° (45° on GKS 18V-57 G)
(12) Parallel guide
(13) Retracting blade guard
(14) Adjusting lever for retracting blade guard
(15) Wing bolt for mitre/bevel angle preselection
(GKS 18V-57 G)
(16) Chip ejector
(17) Protective guard
(18) On/off switch
(19) Battery a)
(20) Handle (insulated gripping surface)
(21) Saw spindle
(22) Mounting flange
(23) Circular saw blade
a)
(24) Clamping flange
(25) Clamping bolt with washer
(26) Battery release button
a)
(27) Fastening screw for dust extraction adapter
(28) Dust extraction adapter a)
(29) Clamping lever for cutting depth preselection
(30) Cutting depth scale
(31) Pair of screw clamps a)
(32) Button for battery charge indicator
(33) Battery charge indicator a)
(34) Guide rail a)
(35) Extraction hose a)
(36) Connection piece a)
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
GKS 18V-57 G
3 601 FA2 1..
V= 18
min -1 3400
a)
a)
GKS 18V-57
3 601 FA2 2..
18
3400
Bosch Power Tools