Publicité
On-Board Tool Cleaning
On-Board Tool Cleaning
These vacuums are equipped with on-board cleaning tools including a metal
These vacuums are equipped with on-board cleaning tools including a metal
telescopic power wand, stretch hose, dusting brush and a crevice tool.
telescopic power wand, stretch hose, dusting brush and a crevice tool.
1.
To use the cleaning tools, lift the hose handle straight up from the vacuum
• To use the cleaning tools, lift the hose handle straight up from
(Fig. 1).
the vacuum (Fig. 1).
2.
extend the wand by pulling the button back and pulling the smaller wand
• Extend the wand by pulling the button back and pulling the smaller
out of the larger wand (Fig. 2).
wand out of the larger wand (Fig. 2).
3.
Attach any of the on-board tools to the end of the wand or if you do not
• Attach any of the on-board tools to the end of the wand or if you
need the wand, any tool can be connected directly onto the hose handle.
do not need the wand, any tool can be connected directly onto
the hose handle.
How to Replace the Vacuum Belt
CAUTION: Unplug the vacuum cleaner before performing any of these steps.
How to Remove the Bottom Plate
How to Replace the Vacuum Belt
• Place the vacuum cleaner in the low position by pressing the foot
pedal release twice while reclining the handle. Turn the vacuum over.
CAUTION: Unplug the vacuum cleaner before performing any of these steps.
• Slide the clips toward each other (Fig. 3).
How to Remove the Bottom Plate
• Remove the bottom plate.
1.
How to Replace the Belt
Place the vacuum cleaner in the low position by pressing the foot
pedal release twice while reclining the handle. Turn the vacuum over.
• Turn the unit over and remove the bottom plate as described in the above section.
2.
Slide the clips toward each other (Fig. 3).
• Remove the belt guard (Fig. 4). Remove the agitator by pulling it straight out (Fig. 5).
3.
Remove the bottom plate.
• Remove the belt from the agitator.
How to Replace the Belt
• Loop a new belt over the motor pulley (Fig. 6) and over the end of the
agitator.
1.
Turn the unit over and remove the bottom plate as described in the above section.
• Stretch the belt over the agitator while inserting it back into the nozzle
2.
Remove the belt guard (Fig. 4). Remove the agitator by pulling it straight out (Fig. 5).
housing.
3.
Remove the belt from the agitator.
• Reinsert the belt guard.
4.
Loop a new belt over the motor pulley (Fig. 6) and over the end of the agitator.
• Spin the agitator by hand to make sure it turns smoothly and the new belt
5.
Stretch the belt over the agitator while inserting it back into the nozzle housing.
is properly aligned.
6.
Reinsert the belt guard.
• Replace the bottom plate by hooking the front end of the plate into the two ribs
on the front end of the nozzle housing. Press the bottom plate into place
7.
Spin the agitator by hand to make sure it turns smoothly and the new belt is
and fasten it with the two screws.
properly aligned.
NOTE: To ensure maximum cleaning effi ciency, check the belt regularly to ensure
8.
Replace the bottom plate by hooking the front end of the plate into the two ribs on
it is in good condition. Replace the belt if it is stretched, cracked or if excessive
the front end of the nozzle housing. Press the bottom plate into place and fasten it
slipping is occurring.
with the two screws.
NOTE: To ensure maximum cleaning effi ciency, check the belt regularly to ensure it is in good
condition. Replace the belt if it is stretched, cracked or if excessive slipping is occurring.
Fig. 1
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Parts & Operations Manual
Parts & Operations Manual
Fig. 2
7
7
Tracker
Tracker
Publicité
