Revell Control QUADROTOX Mode D'emploi page 9

• Never disassemble or alter the battery
contacts. Do not damage or puncture
the battery cells. There is a risk of
explosion!
• The LiPo battery must be kept out of
reach of children.
• When disposing of batteries, they
must be discharged or their capacity
must be fully depleted. Cover exposed
terminals with adhesive tape in order
to prevent short-circuiting!
Maintenance and care:
• Please only use a clean, damp cloth
to wipe off the model.
• Protect the model and batteries from
direct sunlight and/or direct heat.
• Never allow the remote control and
charging unit to come into contact
with water, because the electronics
will be damaged as a result.
Technical changes and differences in
color reserved!
1A Battery port
1B Battery compartment
1C Status LED
2 REMOTE CONTROL
2A Control for thrust and rotation/
press vertically: speeds
2B Control for Forward/
Reverse and Banking/press vertically:
looping function
2C Trim for rotation
2D Trim for forwards/backwards
2E Trim for sideways
2F ON/OFF switch
16
Required batteries for the model:
Power supply:
Rated output:
1 x DC 3,7 V / 2,9 Wh
rechargeable
LiPo battery (included)
Capacity: 780 mAh
Battery requirement for the
remote control:
Power supply:
DC 6 V
Batteries:
4 x 1.5 V "AA"
(not included)
1 MODEL
1D No function
1E Rotors
1F Gears
2G No function
2H short press: Return to Home
long press: headless mode
2I Power LED
2K Display
2L Fine trimming of thrust
2M Battery compartment cover
3 INSERTING BATTERIES (REMOTE CONTROL)
3A Cover (2M) removal. 3B Insert 4 x 1.5 V AA batteries
and pay attention to the
polarity specifications, as
indicated in the battery
compartment.
4 CHARGING THE MODEL
Attention: The battery and motor must cool down for 15 to 30 minutes before charging
and after every flight. Otherwise they can be damaged. The charging process must
be constantly monitored. Always ensure that the charging process takes place on a
fireproof surface in a fire-resistant environment.
• Remove the battery from the model (4A). Plug the USB charger into an open USB port
(4B).
• Insert the battery plug into the charging socket of the charger, making sure that the
polarity is correct (4C). Slide the battery plug gently into the charging socket – DO
NOT USE FORCE. If the battery is not correctly inserted into the charging socket, the
battery may become damaged and, under certain circumstances, cause injury.
• The status LED on the charger will light up red when charging begins.
• The charging process lasts approx. 90 minutes and must be continuously monitored.
The status LED on the USB charger goes out when the charging process is finished.
• Disconnect the battery from the charger and disconnect the charger from the outlet
after the charging is completed.
The model can fly for approx. 8-12 minutes after a charge time of approx.
90 minutes.
Warning notice: The battery does not normally heat up while charging. If it should
become warm or even hot and/or changes to the surface begin to appear, immediately
discontinue the charging process!
5 START PREPARATION
The model must be switched on first in order to connect it to the remote control. To do
this, slide (5A) the battery into the model's battery compartment (1B), insert the battery
plug into the battery port (1A) in the model and close the battery compartment. Do not
use force and make sure that the polarity is correct (5B). Then place the model on an
even, flat and stable surface.
Before switching on the remote control, the control for thrust and rotation (2A) must
point down (5C). To switch on the remote control, move the ON/OFF switch (2F) to
ON and briefly push the control for thrust and rotation up and then down again. After
approx. 3 seconds, the model activates and is ready for use.
Once you have finished flying, switch the model off first and then the remote control.
Unplug the battery from the model and remove the battery from the model.
3C Close the battery
compartment cover.
17