GLOBBER DELUXE GO-UP Serie Mode D'emploi page 5

Keep the instructions for future.
NF-EN-71
Warning! Protective equipment should be worn. Not to be used in traffic.
20 kg max.: Seat mode (ride-on, walking bike)
50 kg max.: Scooter mode
Seat mode: Warning! Not to be used by children over 36 months due to the limited
strength of the seat bracket frame. The seat can only be used with this product
when the steering is completely locked by the parents using the locking button
located at the upper side of the steering assembly. Press down the locking button
in order to lock the steering of the wheels when the seat is to be mounted.
Remove the scooter and all the parts from the box. Set out all the parts and read
the assembly instructions prior to use. Keep the packaging until assembly is
complete.
General instructions
This toy must be assembled by a responsible adult. Prior to use, make sure
that the toy has been assembled properly. Remove all the parts which are not
necessary for play before giving the toy to your child. The toy should be used with
caution since skill is required to avoid falls or collisions causing injury to the user
or third parties.
To use with suitable protective equipment, including a helmet, shoes, elbow, wrist
and knee protectors. Teach the child how to use it safely and responsibly.
Directions:
- T he scooter can be dangerous and can cause traffic accidents when used
on public highways. Don't use on public roads. It is best used on a flat, clean
surface, free of gravel and grease. Avoid bumps and drainage grates that may
cause an accident.
- T he scooter does not include any headlights or lights. It is therefore not suited for
use at night or during periods when visibility is limited.
- A lways use under adult supervision.
- Do not allow more than one child to ride the scooter at the same time.
- Do not use on wet days, or on wet ground.
8
Before and after use:
- Make sure that all locking mechanisms are securely locked.
- C heck the height of the steering system, and make sure the nuts are tightened
and that the handlebars and the front wheel are perpendicular.
- T he minimum height of T-bar has to be locked at the lowest position by switching
the bullet into the lowest hole (see diagram A).
- C heck all of the connection elements: the brake, the steering column's quick
release system and the wheel axles must be adjusted correctly and not
damaged.
- Also check the tyre wear.
INSTALLATION AND USE OF SEAT FOR USE (See page 2)
• GO•UP DELUXE comes with a sturdy seat support frame to better distribute the
load of the seated child. There are 3 different seat heights available: 27 - 31cm.
For a comfortable ride, your child's feet should easily touch the footrest and the
ground.
• Place the footrest under the seat support bar in the correct direction (see
diagram 1). Make sure the spring ball on the side "click" into place.
• Insert the seat support bar into the integrated tube at the front of the scooter
deck between the two front wheels. Make sure the spring ball on the side at
the bottom of the column "click" into place to securely hold the seat frame. (see
diagram 2-3)
• Attach the seat to the seat support bar by slotting in from the top, a guided track
can be found. Go all the way down to get the suitable seat height with engraved
1/2/3, then tighten the knob with both hands to make sure it is securely fixed.
• Warning! Exert all your strength on the seat to check seat support bar is locked
in the place safely before riding.
Ride-on mode:
• Insert the handlebar tube in the back hole of the seat support frame. Align
the spring-loaded buttons with the notches in the seat support frame and lock
(Figure 4). Double check that the spring-loaded button is engaged and locked
correctly.
• Adjust the height of the handle to the parent's preference (4 positions are
possible, see diagram E). Loosen the quick release clamp of the T-bar handle
when adjusting. Tighten the quick release clamp to secure the T-bar handle
after adjustment.
• The parent handlebar can be used to accompany children during use. Install
the footrest (see diagram 1). Place the child's feet on the footrest and the adult
pushes using the parent handle (T-bar).
Walking bike mode:
• Remove the handlebar tube in the back hole of the seat support frame.
• GO•UP DELUXE is provided with an adjustable seat which can be adapted
to the child's height (3 positions). unscrew the knob with and slide up/down
to adjust the seat height. Align the seat through the screw holes in the seat
support frame & retighten the knob with both hands.
• Warning! Make sure children's feet can touch the ground freely in the seat
mode before riding.
Steering: The child pushes with his feet on the floor to advance, while the child's
sitting on the seat. He must proceed with caution at first.
Notes:
• Always check the body frame is securely inserted to the deck by pushing
downward without lifting up loosely.
• Always check the seat knob is securely tightened.
• To remove the footrest, first release the body frame from the deck by pressing
the PUSH button on the side of the deck, then press the spring ball on the body
frame to release the footrest. (Figure 5)
• A GLOBBER cover is provided to cover the hole behind the seat while in ride-
on mode. This can be mounted onto the T-bar's column for storage. (Figure 6)
• The footrest can be stored at the seat's back, simply insert this into the hole
behind the seat. (Figure 6)
SCOOTER ASSEMBLY (see page 3-4)
Insert the T-bar column into the integrated tube at the front of the scooter deck
between the two front wheels. Make sure the two spring balls on either side of the
bottom of the column "click" into place for scooter mode. To release the T-bar or
fold/unfold the scooter, step on the deck with your foot, press the push button on
the side of the deck and pull the T-bar column back at a 30 degree angle. (see
diagram 7-12)
GO•UP DELUXE PLAY comes with a revolutionary light & sound LED module
directly integrated in the seat's handlebar, with different modes.
The different modes are: (Figure 14)
ON: Sound & LED lights activated
MUTE: Only LED lights activated
OFF: Both Sound & LED lights disabled
Activating the light & sound module on GO•UP DELUXE PLAY (Figure13-14)
• Remove the module from the seat's handlebar by turning it anti-clockwise.
• Using the button, choose your preferred mode (MUTE or ON).
• Insert the module back into the seat's handlebar and turn clockwise to lock it.
It's advisable to switch the module OFF when not in use.
Charging the module (Figure 15)
GO•UP DELUXE PLAY light & sound module has an in-built rechargeable battery
which can be charged with a Micro USB cable at the back of the module. Use the
Micro USB cable provided in-pack.
9