Skil 6710 Notice Originale page 11

USE
• On/off 6
• Switch locking for continuous use 7
• Speed control for smooth starting 8
• Maximum speed control 9
With wheel C the maximum speed can be adjusted from
low to high
- switch on the tool
- lock the switch
- turn wheel C to select maximum speed
• Mechanical gear selection q
- set selector E to desired speed
! actuate the gear selector while tool is running
slowly
1 = LOW SPEED
- high torque
- for drilling large diameters
- for tapping thread
2 = HIGH SPEED
- lower torque
- for drilling small diameters
• Changing direction of rotation w
- when not properly set in left/right position, switch A 2
cannot be activated
! change direction of rotation only when tool is at a
complete standstill
• Normal drilling versus impact drilling e
! select drilling function only when tool is switched
off and plug is disconnected
• Changing bits r
- insert the bit as deep as possible in the chuck
! do not use bits with a damaged shank
• Adjusting drilling depth t
• Holding and guiding the tool y
- always use auxiliary handle G 2 (can be adjusted
as illustrated)
! while working, always hold the tool at the grey-
coloured grip area(s)
- keep the ventilation slots uncovered
- do not apply too much pressure on the tool; let the tool
do the work for you
APPLICATION ADVICE
• Use the appropriate bits u
! only use sharp bits
• For drilling in concrete or stone a steady pressure on the
drill is required
When drilling ferrous metals
•
- pre-drill a smaller hole, when a large hole is required
- lubricate drill bit occasionally with oil
Splinterfree drilling in wood i
•
• Dustfree drilling in walls o
• Dustfree drilling in ceilings p
• Drilling in tiles without skidding a
• For more information see www.skil.com
MAINTENANCE / SERVICE
This tool is not intended for professional use
•
• Always keep tool and cord clean (especially ventilation
slots H 2 )
! disconnect the plug before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, please send the
tool undismantled together with proof of purchase to your
dealer.
• Be aware that damage due to overload or improper
handling of the product will be excluded from the
warranty (for the warranty conditions please ask your
dealer).
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 5 will remind you of this when the need for
disposing occurs
NOISE / VIBRATION
• Measured in accordance with EN 60745 the sound
pressure level of this tool is 94.2 dB(A) and the sound
power level 105.2 dB(A) (uncertainty K = 3 dB), and the
vibration ✱ (triax vector sum; uncertainty K = 1.5 m/s²)
when drilling in metal < 2.5 m/s²
✱
when impact drilling in concrete 11.1 m/s²
✱
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60745;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
b
Perceuse à
percussion
INTRODUCTION
• Cet outil est conçu pour les travaux de perçage de
percussion dans la brique ainsi que le perçage dans le
bois, le métal, la céramique et les matières plastiques
• Cet outil n'est pas conçu pour un usage professionnel
• Lisez et conservez ce manuel d'instruction 3
CARACTERISTIQUES TECHNIQUES 1
11
6710