Publicité
Les langues disponibles
Les langues disponibles
Typical Mounting Instructions For Pre-Rinse Assembly
1. PRE-RINSE ASSEMBLY
LESS ADD-ON FAUCET
a. Turn off the water supply at
the source.
b. Apply pipe joint compound or
teflon tape to threads on both
ends of riser pipe. Thread
riser pipe into faucet body
and hand tighten.
RISER
PIPE
TEFLON TAPE
OR PIPE JOINT
COMPOUND
FAUCET BODY
4. ASSEMBLE PRE-RINSE WITH GOOSENECK SPRING
a. Assemble spring retainer to riser pipe and tighten with wrench. This will also tighten riser pipe on faucet body.
b. Assemble hose to spring retainer. Ensure O-ring is in place inside of hose coupling prior to assembly.
(Refer to drawing #1 below). Additional O-rings are provided for future use. Tighten securely.
c. Assemble large coil spring over hose and onto spring retainer. IMPORTANT: Spring must be assembled
vertically with large curve of spring to the top.
d. Assemble spray head ring over spray head grip, and assemble spray head assembly to hose.
Tighten with wrench; ensure O-ring is in place prior to assembling. (Refer to drawing #2 below).
Note: Realign spray head hook on riser and tighten. Tighten all wall bracket screws.
Turn on water and check for leaks.
BE SURE O-RING IS INSTALLED
#1
FOR PROPER PERFORMANCE
(Extra O-rings are provided)
HOSE
COUPLING
CORRECT
DIRECTION
WRONG
DIRECTION
SPRING
RETAINER
IOM-Hydro-Force 1810
1A. PRE-RINSE ASSEMBLY
WITH ADD-ON FAUCET
a. Turn off the water supply at
the source.
b. Apply pipe joint compound or
RISER
teflon tape to threads on end of
PIPE
short riser pipe attached to
ADD-ON
add-on faucet. Thread riser
FAUCET
pipe into faucet body and tighten.
c. Apply pipe joint compound or
teflon tape to threads on both
ends of riser pipe.Thread riser
pipe into add-on faucet body
and hand tighten.
SHORT
RISER PIPE
FAUCET BODY
#2
GRIP
LARGE COIL
POSITIVE SEAL
O-RING
CONSTRUCTION
ELIMINATES NEED
FOR WASHERS
HOSE
STRAIN
RELIEF
SPRING
SPRAY HEAD
HOSE
COUPLING
2. ASSEMBLE SPRAY
HEAD HOOK TO RISER
Spread (open) clamp section
of hook so that it will slide
over riser without marking
finish of riser. Orient spray
head hook with hook facing
up and assemble to riser.
Place approximately one half
downlength of riser.
RISER PIPE
Do not tighten at this time.
SPRAY HEAD
HOOK
CLAMP
Dormont warrants to Buyer that Watts Hydro-Force™ commercial
foodservice products (the "Product") will be free from defects in
material and workmanship for a period of two years from the date
of delivery to the Buyer. For items not manufactured by Dormont,
the only warranty extended is that of the manufacturer, if any. In the
event of defects within the warranty period, Dormont will replace the
Product or other items at Dormont's expense (excluding labor and
freight charges).
To qualify for the warranty remedy stated above, you must obtain
return authorization from Dormont and return the defective Product
or other items in accordance with Dormont's shipping instructions.
All defective returns shall be subject to Dormont's inspection and
approval. This Product and any other items must be installed by
individuals trained and certified as professionals with respect to such
installation, and be installed, used, repaired and maintained by Buyer
in accordance with local codes or regulations, and standards set by
NSF. Any failure to observe these requirements shall void this Limited
Warranty. The Product and other items are warranted in conjunction
SPRING
with the original installation or connection only. Buyer shall not assign
its rights under this Limited Warranty and any attempted assignment
shall render this warranty, but not any disclaimers or limitations, void.
THE WARRANTY SET FORTH HEREIN IS GIVEN EXPRESSLY AND IS
THE ONLY WARRANTY GIVEN BY DORMONT WITH RESPECT TO THE
PRODUCT. DORMONT MAKES NO OTHER WARRANTIES, EXPRESS
OR IMPLIED. DORMONT HEREBY SPECIFICALLY DISCLAIMS ALL
SPRAY
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT
HEAD RING
LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE.
GRIP
3. ASSEMBLE WALL BRACKET
Model No. PRA-WB
BRACKET BASE
Determine correct length of support
rod from wall to riser pipe. Cut
rod to approximate size. Affix wall
bracket base securely to wall. Install
compression nut and bracket ferrule
and tighten securely.
CAUTION! MANUFACTURER RECOMMENDS THE
USE OF WALL BRACKET ASSEMBLY TO SECURE
RISER PIPE ON ALL PRE-RINSE ASSEMBLIES.
NOTE: WALL BRACKET SHOULD BE LOCATED TOWARD TOP OF
RISER PIPE– AS CLOSE AS POSSIBLE TO SPRING RETAINER.
LIMITED WARRANTY
The remedy described in the first paragraph of this Limited Warranty
shall constitute the sole and exclusive remedy for breach of warranty,
and Dormont shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or
the cost of repairing or replacing other property which is damaged if
the Product or other items do not work properly, other costs resulting
from labor charges, delays, vandalism, negligence, fouling caused by
foreign material, damage from adverse conditions, chemicals, or any
other circumstances over which Dormont has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper
installation, improper maintenance, alteration or repair of the Product
or items, damage caused by shipping or conformity of the Product to
local codes or regulations not previously made known to Dormont, or
other occurrences or conditions other than normal use .
Some States do not allow limitations on how long an implied warranty
lasts, and some States do not allow the exclusion or limitation of
incidental or consequential damages. Therefore the above limitations
may not apply to you. This Limited Warranty gives you specific legal
rights, and you may have other rights that vary from State to State.
You should consult applicable state laws to determine your rights.
SO FAR AS IS CONSISTENT WITH APPLICABLE STATE LAW, ANY
IMPLIED WARRANTIES THAT MAY NOT BE DISCLAIMED, INCLUDING
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO ONE
YEAR FROM THE DATE OF ORIGINAL SHIPMENT.
USA: T: (800) 367-6668 • F: (724) 733-4808 • foodservice.watts.com
Canada: T: (905) 332-4090 • F: (905) 332-7068 • foodservice.watts.com
WALL
FERRULE
SUPPORT
ROD
SPRING
RETAINER
COMPRESSION
NUT
RISER PIPE
© 2018 Watts
Publicité
