Publicité
Les langues disponibles
Les langues disponibles
1.1
1.3
- Hot
Black
Tag
Bare
-
Black
To Light
Identify existing wiring (This switch will be a single-pole) and tag "Hot" wire. Use
voltage tester as necessary to confirm "Hot" wire (Voltage will be present at the
"Hot" wire when the lights are off).
1.4
1.6
TOP
Gently push dimmer into place and secure with mounting screws. Make
sure disconnect switch at bottom of master is fully pushed in
2.1
2.1
Red
Bare
Black
Tag
Black
Identify existing wiring (both existing switches will be "3-way")
Tag common wire on both 3-Way switches (see "How to Identify
*
Common Wires" section
)
Master
2.4
2.5
Red
Black
Tag
Green
White
Red
Black
Three Location Control Installation (requires one Master and two Accessory dimmers)
3.1
3.1
Red
Black
Red
Bare
Tag
Tag
Black
Identify existing wiring (4-way switches) Tag common
wire on 4-Way switch. (see "How to Identify Common
*
Wires" section
)
Hot
120V
Traveler Wires
Black
Green
White
Ground
Neutral
White
White
LOCATION A
Cooper Wiring Devices (CWD) warrants its RF Smart Dimmer System to be free of defects in materials and workmanship in normal use and service for a period of two years from date of original purchase. THIS TWO (2) YEAR
LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, OBLIGATIONS, OR LIABILITIES, EXPRESSED OR IMPLIED (INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE THAT IS IN DURATION IN EXCESS OF TWO YEARS FROM THE DATE OF ORIGINAL CONSUMER PURCHASE). NO AGENT, REPRESENTATIVE, OR EMPLOYEE OF CWD HAS AUTHORITY TO INCREASE OR ALTER THE
OBLIGATIONS OF CWD UNDER THIS WARRANTY.
To obtain warranty service for any properly installed CWD RF Smart Dimmer System that proves defective in normal use send the defective RF Smart Dimmer System prepaid and insured to Quality Control Dept., Cooper Wiring
Devices, 203 Cooper Circle, Peachtree City, GA 30269; in Canada: Cooper Wiring Devices, 5925 McLaughlin Road, Mississauga, Ontario L5R 1B8.
CWD will repair or replace the defective unit, at its option. CWD will not be responsible under this warranty if examination shows that the defective condition of the unit was caused by misuse, abuse, improper installation,
alteration, improper maintenance or repair of damage in shipment to CWD.
CWD SHALL HAVE NO RESPONSIBILITY FOR INSTALLATION OF THE RF SMART DIMMER SYSTEM, OR FOR ANY PERSONAL INJURY, PROPERTY DAMAGE, OR ANY SPECIAL, INCIDENTAL, CONTINGENT, OR CONSEQUEN-
TIAL DAMAGES OF ANY KIND, RESULTING FROM DEFECTS IN THE RF SMART DIMMER SYSTEM OR FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT.
THE EXCLUSIVE REMEDY FOR BREACH OF THE LIMITED WARRANTY CONTAINED HEREIN IS THE REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT AT CWD'S OPTION. IMPLIED WARRANTIES (IF ANY) INCLUDING,
BUT NOT LIMITED TO IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABIITY, ARE LIMITED IN DURATION TO A PERIOD ENDING TWO YEARS FROM THE DATE OF ORIGINAL CONSUMER
PURCHASE. IN NO CASE SHALL CWD'S LIABILITY UNDER ANY OTHER REMEDY PRESCRIBED BY LAW EXCEED THE PURCHASE PRICE. Some states do not allow the exclusion or limitation of incidental or consequential dam-
ages or allow disclaimers or modifications of or limitations on how long an implied warranty lasts, so the above limitations may not apply to you. Some Canadian provinces do not allow exclusion or variance of implied warranties
so that some or all of the above limitations may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state and province to province.
Read enclosed instructions carefully. If you have any questions concerning use or care of this product, please write: Consumer Service Division, Cooper Wiring Devices, 203 Cooper Circle, Peachtree City, GA 30269.
Single Location Control Installation (requires one Master dimmer)
White
Two Location Control Installation (requires one Master and one Accessory)
2.2
2.2
White
Black
NOTE: The Circuit Breaker must be turned "ON" during this step
and the switches must be set so that the light is OFF. Ensure
that all wires are safely separated before turning the Circuit
Breaker "ON." Connect the tester between the tagged common
terminal and ground in one of the boxes to determine the location
for the Accessory Dimmer. If the test indicates voltage then that
will be Location A, and will be used for the Accessory Dimmer.
If voltage is not present then the other 3-way location will be
Location A. NOTE: Disconnect power after this step.
White
Hot
120V
Black
Neutral
3.2
3.2
Black
White
Green
ACCESSORY
White
Red
Red
Traveler Wires
Black
Black
Green
White
Ground
Ground
White
White
White
COOPER WIRING DEVICES LIMITED 2 YEAR WARRANTY
1.2
1.4
Disconnect existing switch and remove.
Hot
Black
120V
Green
Ground
Neutral
Red
Bare
Black
Tag
Black
Traveler Wires
Red
Green
White
Ground
White
White
LOCATION A
Connect the second Accessory Dimmer (4-way switch) as shown.
Accessory
4-Way Location
IMPORTANT! How to identify Common Wires
White
Tag
Two location:
Red
Each switch will have insulated wires connected to three terminal screws plus a
green or bare wire connected to a green terminal screw. The three terminals are
Black
usually one dark colored screw and two light colored screws (ignore the Green
screw). Alternatively, the three screws may be the same color and one will be
marked COMMON or COM Find the wires connected to the dark or COMMON
screws. Usually these wires are black but may be red or blue. Tag these wires on
both switches to identify when wiring.
Three location:
Two of the existing switches will be 3-way. The 3-way switches will be located
at each end of the circuit with a 4-way switch in between. TAG the two 3-way
switches as in the Two Location Control section. The 4-Way switch has 4 insu-
Red
lated wires connected to 4 terminal screws. VERY IMPORTANT - TAG two same
Black
color insulated wires, which are connected to screws of opposite colors.
Light Fixture
Green
Refer to 1.4 to push dimmers into place.
1.5
1.3
Black
Green
White
Connect master dimmer as shown by connecting black
wire of dimmer to tagged "Hot" wire. Red wire must
be connected to the wire that goes to the light.
Red
White
White
2.4
2.3
White
Green
ACCESSORY
ACCESSORY
Disconnect existing switch and remove. Connect
Accessory Dimmer in Location A as shown.
Black
Red
Black
Green
Ground
White
Master
Tag
Black
White
Black
Red
Light Fixture
Accessory
LOCATION A
White
Black
Red
Black
Tag
White
Light Fixture
*
Publicité
