CONTINENTAL EDISON CELED483DMLA3 Mode D'emploi page 43

You can download or upload SatcoDX data. In order
to perform these functions a USB device must be
connected to the TV.
You can upload current services and related satellites
& transponders in TV, to a USB device.
Additionally you can download one of the SatcoDx
files stored in USB device, to the TV.
When you select one of these files, all services and
related satellites and transponders in the selected
file will be stored in the TV. If there are any installed
terrestrial, cable and/or analog services, they will be
kept and only satellite services will be removed.
Afterwards, check your antenna settings and make
changes if necessary. An error message stating "No
Signal" may be displayed if the antenna settings are
not configured properly.
Media Playback via USB Input
You can connect a 2.5" and 3.5" inch (hdd with
external power supply) external hard disk drives or
USB memory stick to your TV by using the USB inputs
of the TV.
IMPORTANT! Back up your files before making
any connections to the TV. The Manufacturer
will not be responsible for any file damage or
data loss. Certain types of USB devices (e.g.
MP3 Players) or USB hard disk drives/memory
sticks may not be compatible with this TV. The
TV supports FAT32 and NTFS disk formatting
but recording will not be available with NTFS
formatted disks.
While formatting a USB hard disk that has
1TB (Tera Byte) or more file capacity, you can
experience problems with the formatting process.
Quickly plugging and unplugging USB devices,
is a very hazardous operation. This may cause
physical damage to the USB player and the USB
device itself. Do not pull out the USB module while
playing a file.
You can use USB hubs with your TV's USB inputs.
External power supplied USB hubs are recommended
in such a case.
It is recommended to use the TV's USB input(s)
directly, if you are going to connect a USB hard disk.
Recording a Programme
IMPORTANT: When using a new USB hard disk drive,
it is recommended that you first format the disk using
your TV's "Format Disk" option.
Note: To record a programme, you should first connect
a USB disk to your TV while the TV is switched off.
You should then switch on the TV to enable the
recording feature.
To use the recording function, you need to connect
a USB disk or an external hard disk drive to the TV
and the connected USB disk should have at least 1
GB capacity and should have 2.0 speed compatibility.
If the connected USB device does not support 2.0
speed, an error message will be displayed.
Note: Recorded programmes are saved into the
connected USB disk. If desired, you can store/copy
recordings onto a computer; however, these files will
not be available to be played on a computer. You can
play the recordings only via your TV.
Note: Lip Sync delay may occur during the timeshifting.
Radio record is supported. The TV can record
programmes up to ten hours.
Recorded programmes are split into 4GB partitions.
If the writing speed of the connected USB disk is not
sufficient, the recording may fail and the timeshifting
feature may not be available.
It is recommended to use USB hard disk drive to
recording HD programmes.
Do not plug out the USB/HDD during a recording. This
may harm the connected USB/HDD.
Multipartition support is available. A maximum of two
different partitions are supported. The first partition of
the USB disk is used for PVR ready features. It also
must be formatted as the primary partition to be used
for the PVR ready features.
Some stream packets may not be recorded because of
signal problems, so sometimes the video may freeze
during playback.
Record, Play, Pause, Display (for PlayListDialog) keys
can not be used when teletext is ON. If a recording
starts from the timer when teletext is ON, teletext is
automatically turned off. Also teletext usage is disabled
when there is an ongoing recording or playback.
Timeshift Recording
Press (PAUSE) button while watching a broadcast
to activate timeshifting mode.In timeshifting mode, the
programme is paused and simultaneously recorded
to the connected USB disk. Press
again to resume the paused programme from where
you stopped. Press the STOP button to stop timeshift
recording and return to the live broadcast.
Note: Timeshift cannot be used while in radio mode.
Note: You cannot use the timeshift fast reverse feature
before advancing the playback with the fast forward option.
Instant Recording
Press (RECORD) button to start recording an
event instantly while watching a programme. You can
press (RECORD) button on the remote control
again to record the next event on the EPG. In this
case, an OSD will be displayed, indicating the
programmed events for recording. Press
button to cancel instant recording.
Note: You can not switch broadcasts or view the Media Browser
during the recording mode. While recording a programme or
during the timeshifting, a warning message appears on the
screen if your USB device speed is not sufficent.
English - 42 -
(PLAY) button
(STOP)