Publicité
Les langues disponibles
Les langues disponibles
MAINTENANCE
CAUTION:
Always be sure that the tool is switched off and the bat-
tery cartridge is removed before carrying out any work on
the tool.
Adjusting the cutting angle
This tool is carefully adjusted and aligned at the factory,
but rough handling may have affected the alignment. If
your tool is not aligned properly, perform the following:
1.
Miter angle
Loosen the grip which secures the turn base. Turn
the turn base so that the pointer points to 0° on the
miter scale. Then turn the turn base slightly clock-
wise and counterclockwise to seat the turn base
cozily in the 0° miter notch. (Leave as it is if the
pointer does not point to 0°.) Loosen the four hex
bolts securing the guide fence using the socket
wrench. (Fig. 30)
Lower the handle fully and lock it in the lowered posi-
tion by pushing in the lock pin. Square the side of the
blade with the face of the guide fence using a trian-
gular rule, try square, etc. Then securely tighten the
hex bolts on the guide fence in the order from right
side. (Fig. 31)
Make sure that the pointer points to 0° on the miter
scale. If the pointer does not point to 0°, loosen the
screw which secures the pointer and adjust the
pointer so that it will point to 0°. (Fig. 32)
2.
Bevel angle
i) 0° bevel angle
Lower the handle fully and lock it in the lowered
position by pushing in the lock pin. Loosen the
lever at the rear of the tool. Turn the 0° bevel
angle adjusting bolt (lower bolt) on the right side
of the arm two or three revolutions counterclock-
wise to tilt the blade to the right. (Fig. 33)
Carefully sqaure the side of the blade with the top
surface of the turn base using the triangular rule,
try square, etc. by turning the 0° bevel angle
adjusting bolt clockwise. Then tighten the lever
securely. (Fig. 34)
Make sure that the pointer on the sub arm points
to 0° on the bevel scale on the arm. If it does not
point to 0°, loosen the screw which secures the
pointer and adjust the pointer so that it will point
to 0°. (Fig. 35)
ii) 45° bevel angle
Adjust the 45° bevel angle only after performing
0° bevel angle adjustment. To adjust left 45° bevel
angle, loosen the lever and tilt the blade 45° to the
left. Make sure that the pointer on the sub arm
points to 45° on the bevel scale on the arm. If the
pointer does not point to 45°, turn the 45° bevel
angle adjusting bolt (upper bolt) on the right side
of the arm until the pointer points to 45°. (Fig. 33)
14
Replacement of carbon brushes (Fig. 36 & 37)
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps. Take
out the worn carbon brushes, insert the new ones and
secure the brush holder caps.
To maintain product safety and reliability, repairs, mainte-
nance or adjustment should be carried out by a Makita
Authorized Service Center.
ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita service center.
• Dust bag
• Holder
• Socket wrench 10
• Triangular rule
• Lock-off button (Switch button)
• Vertical vise
• Carbide-tipped saw blade
• Safety goggle
• Holder-rod assembly
• Vise assembly (horizontal vise)
• Set plate
• Holder assembly
• Various type of Makita genuine batteries and chargers
• Battery cover
Publicité
