Publicité
Les langues disponibles
Les langues disponibles
1. On/Off button – Press
machine. The power indicator will light when the machine
is turned on.
2. Low setting button – After turning on the machine, press
to enter the low power/pressure level. The low setting
indicator will light when the machine enters low power/
pressure level. The low power/pressure level reduces the
motor speed for a maximum battery life. It is also ideal for
cleaning everyday dirt + grime.
NOTE: The machine is set to be operated in default high
power/ high pressure level when it is started every time.
You need to press the low setting button if low power/
pressure level is desired. To enter HIGH power/high
pressure level from low power/pressure level, press the
low setting button again. The low setting indicator will turn
off and the machine will increase power and pressure.
3. Error indicator – The error indicator is off when the
machine is working normally. A flashing error indicator
means something is wrong with the machine. Check the
table below for possible causes and solutions for the
flashing error indicator. If the indicator keeps flashing
after all the measures have been taken, please call
the Snow Joe
+ Sun Joe
®
1-866-SNOWJOE (1-866-766-9563)
Error Indicator
Possible Reasons
Flashes for 6
Short circuit
seconds and
shuts down
Flashes for 3 min
• Nozzle is blocked.
and shuts down
• Batteries are flat.
Using the 5-in-1 Quick-connect Nozzle
Before beginning any cleaning task, determine the best spray
setting for the job. The included 5-in-1 Quick-Connect nozzle
features 5 different spray options to match your desired
cleaning application. The nozzle patterns are 40˚ (for gentle
cleaning), 15˚ (for tough jobs), 0˚ (for spot cleaning or hard-to-
reach areas), 0+ (for long range spray), 40+ (for short range
spray).
m
CAUTION!
NEVER change spray pattern without
locking the safety lock on the trigger handle.
to turn on and shut off the
customer service center at
®
Solutions
Please call the
Snow Joe
+ Sun
®
Joe
customer
®
service center at
1-866-SNOWJOE
(1-866-766-9563)
for assistance.
• Clean the nozzle
with the included
needle clean-out
tool.
• Recharge the
batteries.
m
WARNING!
High-pressure jets can be dangerous if
subject to misuse. The jet must not be directed at persons,
pets, live electrical equipment, or the appliance itself.
To change the spray pattern for the nozzle, first make sure the
pressure washer is shut off and not connected with any water
source, and the trigger gun is locked, then twist the nozzle
collar to align the symbol of the desired spray pattern with the
mark on the nozzle (Fig. 25).
Fig. 25
Align with the mark
Working with Detergents
When cleaning with the pressure washer, some cleaning tasks
can be solved with water alone, but for most tasks cleaning
with detergent allows for more effective dirt removal.
m
WARNING!
Use only detergents specifically designed
for use with pressure washers, such as Sun Joe
DECK WASH (SPX-HDC1G), Sun Joe
WASH (SPX-FCS1G), or Sun Joe
(SPX-APC1G). DO NOT USE household detergents, acids,
alkaline solutions, bleaches, solvents, flammable material, or
industrial grade solutions. These could damage the pressure
washer. Many detergents may require mixing prior to use.
Prepare the cleaning solution as instructed on the solution
bottle.
1. Turn off the pressure washer, remove the bucket or shut
off the water supply. Pull the trigger to release water
pressure.
2. Remove the spray wand attachment from the trigger gun.
3. Remove the soap dispenser sprayer from the bottle and
fill with mixed detergent. Put the sprayer back on when
finished.
4. Take the foam cannon and align the two tabs with your
trigger gun. Once aligned, push it into the trigger gun, and
twist counter-clockwise to lock securely into place
(Fig. 26).
14
Multi-spray nozzle
HOUSE +
®
SNOW FOAM AUTO
®
HEAVY DUTY CLEANER
®
Publicité
