Fcc Information U.s.a; Introduction; Installation - Behringer X-MADI Manuel D'utilisation

10 EXPANSION CARD X-MADI
Warning
Failure to observe the following warnings may
lead to fatality or serious injury from fire or
electric shock.
Before installing the card, you must refer to the owner' s
manual of the host device or to behringer.com to verify that
your host device supports this card, and to verify the number
of cards that can be installed in combination with other
BEHRINGER or third-party cards.
• Do not attempt to disassemble or modify the card.
Do not apply excessive force to board connectors or
other board components. Mishandling of board may
lead to shock, fire hazard, or equipment failure.
• Disconnect the power cable from the main unit before
installing this card to eliminate shock hazard.
Caution
Failure to observe the following precautions may
lead to personal injury, or may result in damage
to equipment or other property.
• Do not touch the board's metallic leads (pins)
when handling the card. Pins are sharp and may
cause injury.
• The card is electrostatic-sensitive.
Before handling the card, you should briefly
touch the main unit's metal casing with
your bare hand so as to drain off any static
charge from your body. BEHRINGER assumes no
responsibility for data loss, equipment damage,
or injury caused by inappropriate handling or usage.

FCC INFORMATION U.S.A.

1. IMPORTANT NOTICE: DO NOT MODIFY
THIS UNIT! This product, when installed as indicated
in the instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
BEHRINGER may void your authority, granted by the FCC,
to use the product.
2. IMPORTANT: When connecting this product to
accessories and/or another product, use only high quality
shielded cables. Cables supplied with this product MUST be
used. Follow all installation instructions. Failure to follow
instructions could void your FCC authorization to use this
product in the USA.
3. NOTE: This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class "B" digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will not
result in harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and, if not
installed and used according to the instructions found in
the users manual, may cause interference harmful to the
operation of other electronic devices. Compliance with FCC
regulations does not guarantee that interference will not
occur in all installations. If this product is found to be the
source of interference, which can be determined by turning
the unit "OFF" and "ON", please try to eliminate the problem
by using one of the following measures: Relocate either this
product or the device that is being affected by the interference.
Utilize power outlets that are on different branch circuits
(circuit breaker or fuse) or install AC line filters. In the case of
radio or TV interference, relocate/reorient the antenna. If the
antenna uses 300 Ohm ribbon cable, use coaxial cable instead.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to distribute
this type of product. If you can not locate the appropriate
retailer, please contact BEHRINGER customer service.

1. Introduction

The X-MADI card is a multichannel audio interface expansion
card for the X32 series of digital mixers. It provides 32 channels
of MADI/AES10 input and output via fibre-optic or coaxial cables.
This provides very long cable runs up to 2 km with fiber-optic
connection and allows redundancy when combined with BNC
coaxial connectors.

2. Installation

Before you install the X-MADI card in the expansion slot of the
X32 console, you must check behringer.com to verify whether the
console firmware supports that card.
Caution – before installing the X-MADI card into the console,
you must make sure that the console's power switch is turned off.
Malfunctions or electrical shock may occur otherwise.
1. Make sure that the mixer's power is turned off.
2. Loosen the screws left and right that fasten the slot,
then remove the slot cover or currently-installed card and
keep it in a safe place.
3. Before removing the X-MADI card from its protective bag,
we recommend touching the grounded metal chassis of the
console to prevent electrostatic discharges affecting the
sensitive electronic components. It is generally a good idea
to hold the card either by the face plate or by the two small
handles, but never touching the components on the circuit
board directly.
4. Align both edges of the card with the guide rails inside the
slot and carefully insert the card into the slot. Push the card
all the way into the slot to ensure that the contacts of the
card are correctly inserted into the connector inside.
Quick Start Guide
5. Fasten the card using the included screws. Be aware that
damage or malfunctions may occur if the card is
not fastened.
Requirements
X32 Series console with firmware version 2.0 or higher.
11