SFA SANICUBIC 1 Instructions D'installation Et D'entretien page 5

SECURING THE SANICUBIC
8h
UNIT TO THE FLOOR
The SANICUBIC 1 unit is equipped with
fittings to hold it on the floor and prevent
it from turning or moving.
1- Place the unit on the desired spot.
2- Locate the 2 holes for attachment to
the floor.
3- Place the 2 anchors on the floor.
A
4- Fix the unit in place with the screws.
CONNECTING TO ELECTRICAL SUPPLY
8I
1- All wiring should be in accordance with
the applicable electrical code in your
region. The grinding system requires a
single-phase 120-volt, 15 Amp. sup-
ply. When installed in a bathroom, the
receptacle should be 40 inches away
(in straight line) from a shower or bath-
tub. Connect only receptacle protected
by a ground fault circuit interrupter
(GFCI).
WARNING ! : Risk of electric shock -
this pump is supplied with a grounding
conductor an grounding type attachment
plug to reduce risk of electrical shock. be
certain that it is connected only to a pro-
perly grounding - type receptacle.
REMOTE ALARM BOX
9
1/ General alarms:
High level alarm:
If the water level inside the pump is
unusually high, the red LED alarm will light
up.(Also see note for External wired alarm)
Time alarm:
If the motor runs for over 1 minute, the
red alarm LED will light up.
2/ Resetting the general alarms:
The control panel button can only switch
off the red LED (it turns green) if the
problem causing the alarm is resolved.
3/ Power alarm:
If the green LED on the control panel
is flashing, it means that the electrical
power has temporarily been cut off.
UNIT ALARM
LED
GREEN : Power
RED : Alarm
TOUCH
Override
RESET Alarm
EXTERNAL WIRED ALARM
1
®
REMOTE ALARM MODULE
red
general
alarm
LED
The external alarm box of the
SANICUBIC 1 does not require an
®
independent power supply. It is powered
via the circuit board of the SANICUBIC
In the case of a power outage, a battery
takes over.
CONNECTING
THE ALARM BOX
Connect the alarm
cable directly
to the control
panel. The cable
can extend for
15 Ft for ease of
installation.
1/ The red LED on
the alarm box
goes off (visual
and audible) at
the same time
that the LED on the mounted control
panel does.
2/ The yellow "power" LED shows the
status of the power supply for the
alarm box :
- LED on: normal power
- LED flashing: power supply is faulty.
10 CONFORMITY WITH
STANDARDS
• SANICUBIC 1 is eligible to bear
®
the CSA mark shown with adjacent
indicators "C" and "US". The "C" and
"US" indicators adjacent to the CSA
mark signify that the product has been
tested according to the applicable
CSA (CAN) and ANSI/UL standards
for use in Canada and the USA.
This includes products eligible
bear the designation NTRL. NTRL
(Nationally Recognized Testing
Laboratory) is a designation awarded
by the American Occupational Safety
and Health Administration (OSHA) to
laboratories authorized to award the
certification according to American
standards.
11 COMMISSIONING
1 - Once the plumbing and electrical
connections have been made, check
that the connections are watertight
by letting water flow successively
through each inlet used. Make sure
that the unit is operating correctly by
carrying out at least two start cycles
with water to test the system.
yellow
power
2 - WARNING!
alarm
LED
motor in override status (by
pressing the pushbutton on the
control box) until the pump have
been filled with water. Operation
without water damages the grinding
1.
®
system.
3 - This device is not designed for
persons (including children) with
limited physical, sensory or mental
abilities, or those with minimal
experience and knowledge, unless
they are monitored and are given
the necessary instructions for
using the device, with the help of a
person responsible for their safety.
Monitor children and make sure
they do not play with the device.
12 USE
1- The SANICUBIC
to drain off household waste water.
Any other use will invalidate the
guarantee. The unit is able to
handle the accidental flushing of
sanitary napkins such as condoms,
hygiene articles, etc. The disposal
of oils, solvents, acids or any other
potentially corrosive or explosive
liquids, etc, is not allowed.
2- WARNING: In the event of a power
failure, stop draining any water
from the equipment connected to
the SANICUBIC
3- Do not install or use the unit in a
zone where there is risk of explosion.
13 MAINTENANCE
A visual check of the lift station must be
made once a month to make sure it is
operating correctly, and the installation
must be inspected regularly (once a
year) by a qualified person. Meanwhile
if encounter technical problems, please
ask our after-sales service for advice.
If the power supply cable of the unit is
damaged, it must be replaced by the
manufacturer or its after-sales service to
avoid all danger.
Do not operate the
general
alarm
1 unit is designed
®
1 unit.
®
red
LED