DWT ESS02-187 T Notice Originale page 17

Special safety
Hold the power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring or its
own cord. Cutting accessory contacting a "live" wire
may make exposed metal parts of the power tool "live"
and could give the operator an electric shock�
Safety guidelines during
power tool operation
Orbital sander machines are designed
only for dry grinding of various materials;
never use any liquids - it will result in
short circuit inside the power tool and
cancellation of warranty.
• Avoid stopping an electric tool motor when loaded�
• When grinding small workpieces too light for reliable
fixation, always use clamping appliances.
• Do not work materials containing asbestos�
Asbestos is considered carcinogenic�
• Should power supply fail during work, immediately
turn the tool's switch "Off" in order to avoid accidental
turning of the machine on�
• Do not use damaged or used sanding sheets or
sanding sheets incompliant with the sanding plate
diameter - it may lead to damage of the machined
surface and cause the power tool to bounce
(uncontrolled bounce in an accidental direction)�
• During the work (particularly when working above
the head level) use protective eyewear and dust
mask at all times� The dust created during the work
irritates the eyes and the respiratory system mucous
membranes whereas the dust inhalation may pose a
severe threat to one's health�
• The dust created during the work may be hazardous
to one's health, inflammable or explosive, hence one
should clean the work place at relevant times and
use personal protection means� Always use dust
removal / collection appliances (special vacuum
cleaner, dust bag)�
• When emptying the dust collection device, one
should maintain particular caution� Never dispose of
the dust in an open fire.
• When polishing some materials (paints with lead-
based pigments, wood impregnated with arsenic or
chromium compounds, etc�) carcinogenic or toxic
dusts may be produced� In such case, one should take
following precautions:
• all persons present on site should wear protective
clothes made of thick fabric and special anti-
dust masks (designed for protection against the
hazardous impact of a specific substance);
• the workplace should be well ventilated and dust
containers as well as dust removal devices (special
vacuum cleaners) must be used;
• cleaning of the workplace after work should be
performed by persons equipped with the aforesaid
personal protection means�
Warning:
contained in dust generated in sanding,
cutting, sawing, grinding, drilling and
other construction industry activities
warnings
the chemical substances
may result in cancer, congenital deficiency or be
harmful to the fertility. The ion of some chemical
substances shall be:
• Before any repair and replacement work to the
machine, the power plug must be pulled out firstly.
• The transparent two silicon oxide and other
masonry products in the wall bricks and cement;
the chromium arsenic (CCA) in wood with chemical
treatment� The harm degree of these substances shall
depend on the frequent degree of you carrying out
these works� If you want to reduce the contact with
these chemical substances, please work in the place
with ventilation and you shall use the appliances with
safety certificates (such as the dust mask designed
with tiny dust filter).
Notice the power voltage: in power connection, you
must confirm that if the power voltage is the same
to the voltage marked in the tool's data plate� If the
power voltage is higher than the appropriate voltage,
the accidents will be resulted to the operators, and at
the same time, the tool will be destroyed� Therefore, if
the power voltage has not been confirmed, then you
shall never plug in arbitrarily� On the contrary, when
the power voltage is lower than the required voltage,
the motor will be damaged�
Following symbols are used in the operation manual,
please remember their meanings� Correct interpretation
of the symbols will allow correct and safe use of the
power tool�
Symbol
English
17
Symbols used in
the manual
Meaning
Orbital sander
Sections marked gray - soft
grip (with insulated surface)�
Serial number sticker:
ESS ��� - model;
XX - date of manufacture;
XXXXXXX - serial number�
Read all safety regulations
and instructions�
Wear safety goggles�
Wear ear protectors�