DWT OF-1050 NV Notice Originale page 26

Do not draw up the fastening elements
too tight
thread.
Installing / replacing accessories (see fig. 1-2)
After prolonged operation, the router bit
can become very hot, remove it using
gloves. This will also reduce the risk of
injury by the cutting edge.
• Turn the power tool upside down�
• Press and hold spindle lock 11 (see fig. 1).
• Release nut 12 using the wrench 25�
When replacing collet 28 or installing bush 21 (see
fig. 2):
[OF-1050 NV]
• Unscrew nut 12;
• Replace collet 28;
• Screw nut 12 on spindle 29�
[OF-2100 NV]
• Unscrew nut 12;
• Before removing collet 28 from nut 12, open locking
ring 30;
• If you want to use the router bit with the 8 mm
diameter shank - insert bush 21 into collet 28;
• Tighten nut 12 on spindle 29�
When installing or replacing the router bit:
• Install / replace the router bit, noting that the router
bit shank must be inserted into the collet 28 at least 20
mm deep�
• Tighten nut 12 using the open end wrench 25� Note:
never tighten nut 12 without the router bit - this can
damage collet 28.
After all the operations have been completed, release
spindle lock 11�
Dust extraction system (see fig. 3-4)
• Install cover 9 as shown in figures 3-4.
• Install adaptor 22 as shown in figures 3-4.
• Connect the external dust extracting device to
adaptor 22 (use a suitable adaptor if necessary)�
Guide bushing mounting / dismounting (see
fig. 5-6)
• Install guide bushing 24 into the base plate 4 and fix
it using screws 23 (see fig. 5-6).
• Disassembly operations do in reverse sequen-
ce�
Parallel guide assembly / adjustment / installation
(see fig. 7-9)
• Assemble parallel guide 26 as shown in figures 7
and 8�
• Install parallel guide 26 into base plate 4 and fix it
with wing screws 5�
to avoid damaging
• The parallel guide 26 for OF-2100 NV has an
the adjusting screw 34 which can be used for accurate
adjustment (see fig. 9).
• Disassembly operations do in reverse sequence�
Always use the correct supply voltage: the power
supply voltage must match the information quoted on
the power tool identification plate.
Short-term switching on / off
To switch on, press and hold on / off switch 2, to switch
off - release it�
Long-term switching on / off
Switching on:
Push on / off switch 2 and lock it in the position with
lock-on button 1�
Switching off:
Push and release on / off switch 2�
the power tool operation
Dust collection decreases dust concentra-
tion in the air and prevents build up of dust at
the work station�
While
ways use a vacuum cleaner suitable for collecting
process-generated dust� A special adapter is used to
join the vacuum cleaner to adaptor 22�
Speed selector thumbwheel
Using speed selector thumbwheel 13, you may select
the required spindle speed (also during operation)�
The required speed is dependent on the material and
can be determined with practical trials�
When operating your power tool at a low speed for a
long time, it has to be cooled down for 3 minutes� To
do it, set a maximum speed and leave your power tool
to run idle�
Soft start
[OF-2100 NV]
Soft start (starting current limitation system) allows for
the soft start of the power tool - the router bit spins
up gradually without jerks and recoils, and when the
power tool is turned on, this does not impose an abrupt
load on the power network�
Rotation speed stabilization system
The stabilization system maintains the preset RPM
both at an idle speed and under load� This allows for
the smooth advance of the power tool during operation�
English
26
Initial operating
of the power tool
Switching the power
tool on / off
Dust suction during
operating the power
Design features
of the power tool
tool, al