DWT OF-1050 NV Notice Originale page 24

• The machine shall be operated in rain or humid
environment. You shall not touch the power lines to
avoid fire or electric shock.
• Before the machine is removed from the
workpiece, you shall cut off power switch and
completely stop the milling cutter.
• The hands shall always be far away from the
rotating parts. When the milling cutter is in contact
with the workpiece, you shall not make an attempt to
start the machine�
• After work, the switch shall be turned off first
and then lock knot of guide pillar shall be loosed
to make the machine return to original position.
Safety guidelines during
power tool operation
Before commencing operation
• During machining, do not place the workpiece on
a sturdy surface (concrete, steel, stone, etc�) - when
the router bit passes through the workpiece, you can
damage the router bit and lose control over the power
tool�
• Use the router bits whose allowable rotary speed
does not exceed the rotary speed of the power tool
spindle� Observe manufacturer's recommendations
for router bits use� Do not use router bits that do not
conform to the specifications included in the user's
manual�
• Use only sharp nondefective router bits� Bended,
blunt or cracked router bits must be replaced�
• The router bit shank diameter must match precisely
with the internal diameter of the power tool collet�
• Never use the router bit if its cutting unit diameter
exceeds the diameter of the hole in the base plate�
• Remove all nails or any other metal objects from
blanks before cutting�
• When making cuts in walls or partitions, it is necessary
to find the location of hidden wiring, water-pipes and
gas pipes� Severe injuries may occur as a result of
damaging electric wiring or household utility lines�
During operation
• When turning the power on and during operation,
hold the power tool with both hands by both handles
and keep a steady position, which will allow you to
keep control over the power tool�
• Keep your hands at a safe distance from the
rotating router bit� Remember that when machining a
workpiece, the router bit end occasionally protrudes
beyond the lower part of the workpiece and is not
protected - touching it may cause severe injuries�
Never touch the rotating router bit with your hands�
• Never start the machining until the router bit reaches
its full speed�
• Advance the router bit to the workpiece only with the
power tool turned on, otherwise the router bit may be
pinched in a workpiece, or a recoil and loss of control
over the power tool can occur�
• When processing small blanks, use clamping devic-
es. If the blanks are too small to be fixed properly - do
not process them�
• Never remove sawdust while the power tool motor
is running�
• Do not work materials containing asbestos�
Asbestos is considered carcinogenic�
• Avoid stopping an electric tool motor when loaded�
• Avoid overheating your power tool, when using it for
a long time�
• Never operate the power tool over your head level�
After finishing operation
• The power tool may be removed from the workplace
only after it is turned off and the router bit stops
completely�
• Decelerating the router bit rotation by inertia using
the spindle keylock is strictly forbidden- this will put the
power tool out of operation and void your right to the
warranty service�
• During operation the router bit runs very hot - do not
touch it until it cools down�
• Cleaning of the workplace after work should be
performed by persons equipped with the aforesaid
personal protection means�
Warning:
contained in dust generated in sanding,
cutting, sawing, grinding, drilling and
other construction industry activities
may result in cancer, congenital deficiency or be
harmful to the fertility. The ion of some chemical
substances shall be:
• Before any repair and replacement work to the
machine, the power plug must be pulled out firstly.
• The transparent two silicon oxide and other
masonry products in the wall bricks and cement;
the chromium arsenic (CCA) in wood with chemical
treatment� The harm degree of these substances shall
depend on the frequent degree of you carrying out
these works� If you want to reduce the contact with
these chemical substances, please work in the place
with ventilation and you shall use the appliances with
safety certificates (such as the dust mask designed
with tiny dust filter).
Notice the power voltage: in power connection, you
must confirm that if the power voltage is the same
to the voltage marked in the tool's data plate� If the
power voltage is higher than the appropriate voltage,
the accidents will be resulted to the operators, and at
the same time, the tool will be destroyed� Therefore, if
the power voltage has not been confirmed, then you
shall never plug in arbitrarily� On the contrary, when
the power voltage is lower than the required voltage,
the motor will be damaged�
Following symbols are used in the operation manual,
please remember their meanings� Correct interpretation
of the symbols will allow correct and safe use of the
power tool�
Symbol
English
24
the chemical
Symbols used in
the manual
Meaning
Serial number sticker:
OF ��� - model;
XX - date of manufacture;
XXXXXXX - serial number�
substances