Table des Matières
Publicité
1-1. Servicing Filter
7-2.
Servicing Filter
3
rubbergloves
weldgloves
rubbergloves
weldgloves
glasses
OM-244785 Page 22
allen_wrench
4
pliers
solderiron
torque screwdriver
torque wrench
earmuffs
ear plugs
strapwrench
earmuffs
hairdryer
cclamp
!
!
!
!
2
!
1
!
!
6
than 43 psi (296 kPa) to clean filter or filter
may be damaged.
allen_set
1
2
3
4
5
6
needlenose
Open top latches. Carefully remove blower
assembly.
the lower half of the unit.
Wipe off hatch. Starting at the top, use clean
dry, oil-free compressed air (43 psi [296 kPa]
max) to clean the inside of the filter cartridge.
Keep air nozzle at least 2 in. (5 cm) from filter
material. Particles on the outside of filter will
collect in the collection tray at the bottom of
the unit. Be sure to clean the entire surface
stripcrimp
of the filter.
Remove collection tray and dispose of col-
lected particles.
Remove debris from grommet and fitting on
filter case section. Reassemble unit.
tools/
5
Reconnect power. Turn on unit and check
Filter Monitoring light. Repeat filter cleaning
procedure if Filter Monitoring light is on or the
air flow is too low to extract fumes.
socket wrench
electrodewrench
245353-F
tools/
ear plugs
electrodewrench
airgun
rpmmeter
benchvise
Turn off power and disconnect input
power cord.
Do not operate unit without filter or
with dirty (plugged) filter.
Allow cooling period before inspect-
ing or replacing filter, or cleaning par-
Turn off power and disconnect in-
ticle tray.
put power cord.
Do not breathe the particles collected
by the fume extractor. Wear approved
Do not operate unit without filter or
safety equipment (respirator, gloves,
with dirty (plugged) filter.
long sleeve shirt) when servicing fil-
Allow cooling period before in-
ter and spark guard. Dispose of used
specting or replacing filter, or
element and collected particles ac-
cleaning particle tray.
cording to local, state, and federal re-
quirements.
Do not breathe the particles col-
lected by the fume extractor. Wear
Read and understand the Safety Data
approved safety equipment (respi-
Sheets (SDSs) and the manufactur-
rator, gloves, long sleeve shirt)
er's instructions for metals, consum-
when servicing filter and spark
ables, coatings, cleaners, and de-
greasers.
guard. Dispose of used element
and collected particles according
Replace filter if, after cleaning, Filter
to
local,
state,
Monitoring light is on (unit must be
requirements.
turned on) or flow is too low to extract
fumes.
Read and understand the Safety
tools/
Data Sheets (SDSs) and the manu-
Keep collection hose attached to
facturer's instructions for metals,
connection port when servicing filter.
consumables, coatings, cleaners,
Do not use air pressure greater
and degreasers.
Replace filter if, after cleaning, Fil-
flathead
ter Monitoring light is on (unit must
Latch
be turned on) or airflow is too low
Blower Assembly
to extract fumes.
Filter
Keep collection hose attached to
Air Nozzle
connection port when servicing
Particle Collection Tray
filter
Static Pressure Sensing Passage
NOTICE – Do not use air pressure greater
(Grommet/Fitting)
than 43 psi (296 kPa) to clean filter or filter
may be damaged.
knife
steelbrush
1 Latch
Do not damage the seal around
2 Blower Assembly
3 Filter
4 Air Nozzle
5 Particle Collection Tray
6 Static Pressure Sensing Passage (Grom-
heavy-duty workclamp
light-duty workclamp
met/Fitting)
Open top latches. Carefully remove blower
assembly.
NOTICE – Do not damage the seal around
the lower half of the unit.
Wipe off hatch. Starting at the top, use clean
Be sure to align filter monitoring tube
dry, oil-free compressed air (43 psi [296 kPa]
with grommet in lower section.
max) to clean the inside of the filter cartridge.
Keep air nozzle at least 2 in. (5 cm) from filter
material. Particles on the outside of filter will
collect in the collection tray at the bottom of
the unit. Be sure to clean the entire surface
Tools Needed:
of the filter.
drill
Remove collection tray and dispose of col-
helmet
weldshield
lected particles.
Remove debris from grommet and fitting on
Respirator
filter case section. Reassemble unit.
handream
�
airgun
Be sure to align filter monitoring tube
with grommet in lower section.
Reconnect power. Turn on unit and check
OM-244785 Page 1
Filter Monitoring light. Repeat filter cleaning
procedure if Filter Monitoring light is on or
the air flow is too low to extract fumes.
hammer
awl
helmet
weldshield
popriveter
and
federal
philips head
nutdriver
wirec
greasegun
faceshield
file
faceshield
Publicité
Table des Matières
