Publicité
1
en
CONTENTS
IDENTIFICATION OF PART
Series BS is a line of hot air generators with direct heating
system that mix the heat released externally with combustion
residues. These heaters are particularly suitable to be used for
heating, defrosting and drying both outdoors and in areas with
frequent air exchanges.
Series BVS is a line of hot air generators with indirect heating
system. These generators have a heat exchanger that enables
to separate exhaust combustion gases from the heat released in
the environment, so that it is possible to inject a flow of clean hot
air in the area that needs to be heated and to discharge exhaust
fumes externally.
Series BS and BVS hot air generators are designed in
compliance with current safety, performance and life standards,
are fitted with safety devices configured to guarantee continuous
operation, minimize noise and are manufactured in carefully
selected materials that ensure maximum reliability.
Their excellent standalone performances along with the
possibility of using a thermostat guarantee utmost flexibility
during use.
Figur 1
SAFETY INFORMATION
WARNING
IMPORTANT: Read the manual carefully before attempting
to assemble,switch on or service this heater. The use of
the heater may cause serious or fatal injuries resulting
from burns, fire, explosion, electrical discharge or carbon
monoxide poisoning.
DANGER: Carbon monoxide poisoning can be fatal!
Carbon monoxide poisoning - The first symptoms of carbon
monoxide poisoning are similar to those of flu, with headache,
dizziness and/or nausea.These symptoms may be caused by
the defective functioning of the heater. Go outside into the open
air immediately! Have the heater repaired. Some people feel
the effects of carbon monoxide to a greater extent, especially
pregnant women, those suffering from anaemia, cardiac or lung
conditions, those who are drunk and anyone at a high altitu-
de. Ensure that you have read and understood all the warnings.
Keep this manual for future reference - it is a guide to the safe
and correct functioning of the heater.
• Use only fuel oil no.1 in order to avoid the risk of fire or ex-
plosion. Never use petrol, naphtha, paint solvents, alcohol or
other highly inflammable combustibles.
• Fuelling:
a) The individual responsible for fuelling the heater must have
the relevant competence and be completely familiar with the
manufacturer's instructions and with current norms concer-
ning the safe fuelling of the heaters.
b) Only use the type of fuel expressly specified on the identifica-
tion label of the heater.
c) Before adding fuel, extinguish all flames, including the pilot
light, and wait until the heater has cooled down.
d) While adding fuel, inspect all the fuel lines and joins to make
sure there are no leaks. Any leak whatsoever must be repai-
red before switching on the heater.
e) In no circumstances must more than one day's supply of
1. Hot air
fuel be stored in the same building in proximity to the heater.
output, 2.
Fuel storage tanks must be kept in a separate location.
Flue con-
f) All fuel tanks must be kept at a minimum distance from hea-
nection
ters, oxyacetylene torches, welding equipment etc. (with the
(BVS),
exception of the fuel tank incorporated into the heater) fol-
3. Upper
lowing regulations.
shell, 4. Fan
g) Wherever possible, fuel should be stored in a place where the
guard,
floor does not allow fuel to seep through and drip onto live
5. Power
flames beneath, which might cause fire.
cable,
h) Fuel must be stored in compliance with current norms.
• Never use the heater anywhere where petrol, paint solvents or
other highly inflammable vapours are present.
7. Lower
• While using the heater, follow all local ordinances and current
shell.
norms.
• Heaters used in the proximity of tarpaulins, curtains or other
covering materials must be situated at a safe distance fol-
lowing regulations.
It
is
These materials should be fixed safely so as to ensure that
they do not catch fire and are not blown by the wind.
• Only use in locations where there are no inflammable fumes or
high concentrations of dust.
• Power the heater only with electric power that has the voltage,
frequency and number of phases specified on the identification
label.
• Only use earthed three-wire extension cords.
also
recommended
to
use
fireproof
materials.
Publicité
Chapitres
