Favero COIN TIMER Livret D'instructions page 13

You start from the time zero of the first day of the
week and, according to the choice you have made
A
at the step " ", it will be necessary to programme
only day 1 or the whole week (from 1 to 7).
You can programme a maximum of 28 tariff
changes during the whole week. If you pass this
FULL
value the word "
Once finished, you can control the different time
zones with the TOTAL
visualize the hour of each tariff change.
To proceed to the next step press
2 12 : 37 : 37 PROGRAMMING OF THE
2
INTERNAL CLOCK
Hours Minutes
Actual day of the week (from 1 to 7)
This stage is to be bypassed if the time zones were
A
not activated in step " ".
In this step you can programme the internal clock.
The flashing value can be changed with the ( ) and
( ) buttons. With the – F1
value to change.
Press PROG to end programming.
OPERATING
With the inserting of the first coin or banknote the
following situations arise:
1) the opening of the BOX containing the balls, if it
exists;
2) the loading of the time corresponding to the
value of the coin or banknote;
3) the closing of the SERVICE
5-6 ).
Inserting more than one coin or banknote, the time
is accumulated in proportion to the current tariff up
to a maximum of 9 h. and 59 min.
An acoustic signal of one sec. warns the player
twice: respectively at two minutes and one minute
before the end of the loaded time. Moreover,
during the last minute the closing of the
contact (terminals 7-8 ) takes place.
Once the time is over, the
(closing, in this way, the load which is connected to
it). In the COIN TIMER equipped with the BOX, if
all the balls have not been closed in the BOX, an
acoustic signal sounds continuously and the
ALARM contact is activated in an intermittent way,
causing the eventual light connected to it to flash.
The FREE PLAY button allows the operator to
make the COIN TIMER operate freely. To set to
zero the time loaded whilst trying the coin validator
or the banknote validator, press twice the
PLAY button.
" will be visualized.
button, which allows you to
PROG .
+
button you choose which
contact (terminals
ALARM
SERVICE contact opens
FREE
TOTALIZERS
Press the TOTAL
intake. If coins with less than the unit value are
used (eg. 0.50 - 0.10), the decimal figures will not
be shown. The totalizer goes up to 999.999.999
and then starts from zero again.
The visualization can take place in 2 different
times, if the value is more than 6 numbers
(999.999).
Example of visualization of 23.500 (only once):
_23 .500
Example of visualization of 123.458.000 (in two
steps):
for one
__123 .
second;
The visualization of the totalizer disappears if you
press the TOTAL button, or automatically after 12
sec.
If the F1 button is kept pressed for 5 seconds
during this time, the totalizer and all the coin
counters will be reset. Pressing the ( ) button while
the totalizer is visualized you can run successively
the 9 money counters, the counter of the time
passed from the last zero setting and the 2 anti-
fraud counters. They are all marked by the flashing
number on the left of the display. With the ( )
button you can go back.
1 1 0468 0468
MONEY COUNTER 1
9 0193 9 0193
MONEY COUNTER 9
Each money counter visualizes up to 99.999 and
then restarts from zero.
To proceed to the next step press ( ).
TIME PAST FROM
305.20
THE LAST ZERO SETTING
Days Hours
It visualizes the time past from the last zero setting
of the totalizers.
The maximum counting arrives at 999 days and 23
hours, then it restarts from zero.
To proceed on to the next step press ( ).
If the COIN TIMER does not have the balls BOX,
t h e s u c c e s s i v e s t e p s a r e s k i p p e d a n d t h e
visualizing of the counters ends.
In case the COIN TIMER incorporates the BOX,
after the former counters two ANTI-FRAUD
COUNTERS will appear.
F 35 : 42 : 42
TIMER "OFF";
F
how long the BOX has been left
Hours Minutes
open whilst the time was over and
without electricity (OFF). To set it to zero press
To proceed on to the next step press ( ).
12
ENGLISH
button to see the total money
for three
458 .000
seconds.
+
+
+
this indicates for
+
–
F1 .