Skil 1415 Notice Originale page 10

• Always disconnect plug from power source before
making any adjustment or changing any accessory
ACCESSORIES
• SKIL can assure lawless functioning of the tool only
when original accessories are used
• Use only accessories recommended by SKIL
• For mounting/using non-SKIL accessories observe the
instructions of the manufacturer concerned
• Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool
• Do not use damaged, deformed or vibrating accessories
• Handle and store grinding/cutting discs carefully to avoid
chipping and cracking
• Protect accessories from impact, shock and grease
• Never use grinding discs over 32 mm (1 1/4") Ø
• Never use drill bits over 3.2 mm (1/8") Ø
• Never use a cutting disc for side grinding
• Never use reducors or adaptors to it large-hole grinding/
cutting discs
BEFORE USE
• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)
• Do not work materials containing asbestos (asbestos
is considered carcinogenic)
• Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
• Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
• Wear protective glasses and hearing protection 4,
protective gloves and sturdy shoes; when necessary, also
wear an apron
• Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
• Certain kinds of dust are classiied as carcinogenic (such
as oak and beech dust) especially in conjunction with
additives for wood conditioning; wear a dust mask and
work with a dust extraction device when connectable
• Follow the dust-related national requirements for the
materials you want to work with
• Ensure that the collet size corresponds with the shaft size
of the accessory
• Be sure tool is switched of when plugging in
DURING USE
• Use auxiliary handle(s), if supplied with the tool
(loss of control can cause personal injury)
• Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord (a cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock)
• Always keep the cord away from moving parts of the tool;
direct the cord to the rear, away from the tool
• Never use the tool when cord is damaged; have it
replaced by a qualiied person
• Never use spindle lock while tool is running (damage
due to improper handling will be excluded from the
guarantee)
• Keep hands away from rotating accessories
• When grinding metal, sparks are generated; keep other
persons and combustible material from work area
• Keep the ventilation slots uncovered while working
• In case of electrical or mechanical malfunction,
immediately switch of the tool and disconnect the plug
AFTER USE
• The accessory continues to rotate for a short time after
the tool has been switched of
• Before you put down the tool, switch of the motor and
ensure that all moving parts have come to a complete
standstill
• After switching of the tool, never stop the rotation of the
accessory by a force applied against it
• Store tool in locations where temperature will not exceed
50°C
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
• If for any reason the old plug is cut of the cord of this tool,
it must be disposed of safely and not left unattended
USE
• Changing accessories 5
! switch off the tool and disconnect the plug
! ensure that collet size corresponds with shaft
size of accessory
- push spindle-lock button B and hold it while you turn
collet nut D by hand until the spindle lock prevents
further rotation and loosen collet nut D with wrench E
- insert an accessory in collet C as far as possible to
minimize run-out and unbalance
- push spindle-lock button B and hold it while you
tighten collet nut D with wrench E
! avoid excessive tightening of collet nut D
! never tighten collet nut, if there is no accessory
in collet; collet may be damaged
• Changing collets 6
! switch off the tool and disconnect the plug
- push spindle-lock button B and hold it while you
remove collet nut D
- remove collet C
- insert new collet
! never tighten collet nut, if there is no accessory
in collet; collet may be damaged
• Before using the tool
- ensure that accessory is correctly mounted and irmly
tightened
- check if accessory runs freely by turning it by hand
- test-run tool for at least 30 seconds at highest no-load
speed in a safe position
- stop immediately in case of considerable vibration or
other defects and check tool to determine the cause
• On/of switch 7
- switch on/of the tool by pushing knob A in "I"/"O"
position
! before the accessory reaches the workpiece, the
tool should run at full speed
10