Miter Scale Adjustment; Miter Pointer Adjustment; Bevel Square To Table; Bevel Pointer - DeWalt DW718 Guide D'utilisation

Once made, these adjustments should remain accurate.
Take a little time now to follow these directions carefully to
maintain the accuracy of which your saw is capable.
MITER SCALE ADJUSTMENT (FIG. 5)
Place a square against the saw's fence and blade, as
shown. (Do not touch the tips of the blade teeth with the
square. To do so will cause an inaccurate measure ment.)
Loosen the miter lock handle and swing the miter arm
until the miter latch locks it at the 0 miter position. Do
not tighten the lock handle. If the saw blade is not exactly
perpendicular to the fence, loosen the four screws that
hold the miter scale to the base and move the scale left
or right until the blade is perpendicular to the fence, as
measured with the square. Retighten the four screws.
Pay no attention to the reading of the miter pointer at this
time.
MITER POINTER ADJUSTMENT (FIG. 6, 7)
Loosen the miter lock handle to move the miter arm to
the zero position. With the miter lock handle loose allow
the miter latch to snap into place as you rotate the miter
arm to zero. Observe the pointer and miter scale shown
in Figure 6. If the pointer does not indicate exactly zero,
loosen the screw holding the pointer in place, reposition
the pointer and tighten the screw.
BEVEL SQUARE TO TABLE ADJUSTMENT (FIG. 8)
To align the blade square to the table, lock the arm in the
down position. Place a square against the blade and table
taking care to have the square not touch a blade tooth.
Loosen the bevel lock handle and ensure the bevel latch
has firmly snapped into place at 0º. If the saw blade is not
exactly perpendicular to the table, loosen the three nuts
which hold the bevel detent plates to the table. Adjust the
center nut to allow slight drag between it and the table.
Gently tap the motor or the belt cover to move the upper
assembly until the blade is square to the table. Tighten the
center nut. The 45 bevel stops require adjustment after the
bevel square to table adjustment is complete.
BEVEL POINTER (FIG. 8)
If the bevel pointers do not indicate zero, loosen each
screw that holds each bevel pointer in place and move
them as necessary.
BEVEL STOP 45º RIGHT AND LEFT ADJUSTMENT
(FIG. 8)
Your saw has two 45º bevel adjustments, one for the right,
and one for the left. The procedure is the same for each.
To align the 45º stops, lock the arm in the down position.
Place a speed square against the blade and table taking
care to have the square not touch a blade tooth. Loosen
the bevel lock lever and ensure the bevel latch has firmly
snapped into place at 45º. If the saw blade is not 45º to the
table, loosen the nut which holds the 45 bevel latch plate
to the table. Rotate the adjustment screw counterclock-
wise one or two turns so that the blade is less than 45º to
FIG. 5
FIG. 6
MITER
POINTER
FIG. 7
MITER LATCH
MITER LOCK
OVERRIDE
HANDLE
FIG. 8
RIGHT 45º BEVEL
0º BEVEL
LATCH PLATE
LATCH PLATE
LEFT 45º BEVEL
LATCH PLATE
LEFT 45º BEVEL
ADJUSTMENT
SCREW
LEFT 45º BEVEL
PLATE LOCK NUT
LEFT BEVEL
POINTER
RIGHT 45º BEVEL
0º BEVEL
PLATE LOCK NUT
LOCK NUT
8 8
the table. Turn the adjustment screw clockwise until the
blade is 45º to the table. Tighten the lock nut.
FIG. 9
MITER
SCALE
BLADE WRENCH
MITER LATCH
BUTTON
FENCE ADJUSTMENT (FIG. 9)
WARNING: Turn off tool and disconnect from power
source before attempting to move it, changing accesso-
ries or making any adjustments accept as written in laser
adjustment instructions.
In order that the saw can bevel to a full 48º left or right,
one of the fences can be adjusted to provide clearance.
To adjust the fences, loosen a plastic knob and slide the
fence outward. Make a dry run with the saw turned off and
check for clearance. Adjust the fence to be as close to the
blade as practical to provide max imum workpiece sup-
port, without interfering with arm up and down movement.
Tighten knob securely. When the bevel operations are
complete, don't forget to relocate the fence.
NOTE: The guide groove of the fences can become
clogged with sawdust. If you notice that it is becoming
clogged, use a stick or some low pressure air to clear the
guide groove.

AUTOMATIC ELECTRIC BRAKE

Your saw is equipped with an automatic electric blade
brake which stops the saw blade within 5 seconds of trig-
RIGHT 45º BEVEL
ger release. This is not adjustable.
ADJUSTMENT
SCREW
On occasion, there may be a delay after trigger release to
brake engagement. On rare occasions, the brake may not
RIGHT BEVEL
POINTER engage at all and the blade will coast to a stop.
If a delay or "skipping" occurs, turn the saw on and off 4 or
5 times. If the condition persists, have the tool serviced by
an authorized D WALT service center.
E
Always be sure the blade has stopped before removing it
from the kerf. The brake is not a substitute for guards or for
ensuring your own safety by giving the saw your complete
attention.
FENCE KNOB
(one each side)