Publicité
GENERAL SAFETY RULES
READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below, may result in
electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
1.
Know your work light. Read this
manual carefully to learn your work
light's applications and limitations as
well as potential hazards associated
with this type of tool.
2.
A battery operated tool with inte-
gral batteries or a separate bat-
tery pack must be recharged only
with the specified charger for the
battery. A charger that may be suit-
able for one type of battery may cre-
ate a risk of fire when used with an-
other battery.
3.
Use battery operated tool only
with specifically designated bat-
tery pack. Use of any other batteries
may create a risk of fire.
4.
Use only accessories that are rec-
ommended by the manufacturer
for your model. Accessories that
may be suitable for one tool may cre-
ate a risk of injury when used on an-
other tool.
5.
Disconnect battery pack from tool
or place the switch in the locked
or off position before making any
adjustments, changing accesso-
ries, or storing the tool. Such pre-
ventive safety measures reduce the
risk of starting the tool accidentally.
Symbology
Properly Recycle
Nickel Cadmium
Batteries
Direct Current
Underwriters
Laboratories, Inc.
WARNING!
6.
Maintain tool carefully. Keep
handles dry, clean and free from oil
and grease. Follow instructions for
changing accessories. Have damaged
parts repaired or replaced by a MIL-
WAUKEE service facility.
7.
Store idle tools out of reach of
children and other untrained per-
sons. Tools are dangerous in the
hands of untrained users.
8.
When battery pack is not in use,
keep it away from other metal ob-
jects like: paper clips, coins, keys,
nails, screws, or other small
metal objects that can make a
connection from one terminal to
another. Shorting the battery termi-
nals together may cause sparks,
burns, or a fire.
9.
Never insert anything into the
light
bulb
socket
MILWAUKEE replacement light bulbs.
Inserting objects other than light bulbs
may cause short circuit of battery and
personal injury.
10. Maintain labels and nameplates.
These carry important information. If
unreadable or missing, contact a MIL-
WAUKEE service facility for a free
replacement.
Specifications
Power-Plus
Cat. No.
Batteries
Volts
49-24-0150
48-11-1900
12
49-24-0150
48-11-1950
12
49-24-0150
48-11-1960
12
49-24-0150
48-11-1024
14.4
49-24-0150
48-11-1000
14.4
49-24-0160
48-11-2200
18
49-24-0160
48-11-2230
18
2
Always lock trigger or remove bat-
tery pack before changing or re-
moving accessories. Only use ac-
cessories
mended for this tool. Others may
be hazardous.
Removing Battery Pack from Tool
Push in the release buttons and remove
the battery pack.
Inserting Battery Pack into Tool
Insert the battery pack from the front by
pressing in the release buttons and sliding
battery pack into the body of the tool. In-
sert the battery pack until clamp engages.
To reduce the risk of injury, do not
look directly into the light when the
Work Light is on.
Press the trigger to turn "ON" the work
light. Press the trigger again to turn "OFF".
except
Adjusting the pivot head (Fig. 1)
The pivot head can pivot to a range of 120°;
90° up and 30° down with detents every
10°. Pivot head to desired position (Fig. 1).
Allow the detent to snap into place. Do not
forcibly pivot the head.
Fig. 1
A m p
Hours
2
1.3
1.3
2.4
Attaching the Hook for Hanging the
1.7
Work Light
2.0
The work light comes with a detachable
2.4
hook for hanging. The hook can be attached
in two locations on the back of the handle.
ASSEMBLY
WARNING!
Replacing the Light Bulb (Fig. 2)
To reduce the risk of injury, DO NOT
specifically
recom-
operate work light without bezel
assembly in place. Light bulb does
get hot.
1.
Remove battery pack before chang-
ing light bulb.
2.
Unscrew the bezel on pivot head by
turning counterclockwise.
3.
Remove the bezel assembly.
4.
Press gently on the bulb and slide re-
taining clip to the side.
5.
Carefully remove the bulb.
Fig. 2
WARNING!
Label
Bezel
assembly
To reduce the risk of injury and
damage, never insert objects
other than bulbs in the bulb
socket.
To install new bulb, follow above direc-
tions in reverse.
For Work Light 49-24-0150, use replace-
ment bulb 49-81-0020.
For Work Light 49-24-0160, use replace-
ment bulb 49-81-0030.
A spare bulb is provided with the Work
Light. The bulb is located inside the front of
the pivot head, behind the bezel assembly.
See your nearest MILWAUKEE Retailer or
Service Center to obtain replacement bulbs.
3
WARNING!
Spare light bulb
Retaining
clip
Light
bulb
WARNING!
Publicité
