Tylo CC300T Mode D'emploi page 7

by 15 minutes. Press [OK] when the desired start time is displayed. Then
set the desired switch-off time and press [OK]. Indicate whether the
facility is to be on, off or on stand-by for the time chosen The ON/OFF
symbol shows green if the facility is to be on, red if it is to be off and
orange for stand-by. When selecting the ON mode, you must also set the
desired temperature and humidity. Use the arrow keys and confirm with
[OK]. To program a new value, press the right button once to highlight
[Add] and then press [OK]. Then repeat the procedure described above.
To return to the Normal display, select [Back] and confirm with [OK].
Select [Back] once more and then [OK]. If no buttons are pressed, the
control panel automatically reverts to the Normal display after approx. 30
seconds. To delete all pre-programmed times, select [Clear calendar].
You can also temporarily deactivate all programmed values by selecting
[Calendar OFF].
For a simple overview of the pre-programmed schedule select [Overview]
in the Program display. A schematic bar chart diagram shows red for
times when the facility is switched off, green when it is in operation and
yellow when it is on stand-by.
When ON is pressed while the bathing facility is in stand-by mode, the
temperature immediately begins to rise to the pre-set value for bathing.
After 1 hour, the temperature automatically reverts to the stand-by
temperature. Each time the ON button is pressed, a new 1-hour
operating cycle is started.
When the facility is in the OFF mode, the settings are those that were
entered as part of the initial start-up process.
At any time while the facility is operational, you can switch it off manually
by pressing OFF. (This switches off only the current bathing cycle.)
If the humidity level exceeds 30% when the equipment is switched off, an
automatic drying cycle will be activated. This takes about 20 minutes
(factory setting).
You can also deactivate the entire calendar function temporarily, for
example, to carry out service or maintenance, and then reactivate it.
BATHING OUTSIDE PROGRAMMED TIMES
if the control panel's security code function has been activated.
The Tylarium can also be used at times other than those that have been
programmed. Pressing ON starts a 1-hour bathing cycle. To prolong the
bathing period, simply press ON again. The bathing cycle is terminated
automatically 1 hour after the ON button has last been pressed.
IMPORTANT! Don't forget to use the security code to lock the panel.
PANEL SETTINGS
Display.
LCD brightness.
Select [MENU] in the Normal display, [Service] and then [Display].
Highlight [(Brightness (%)] and press the middle button. The highlighted
text then turns dark blue and the value for the brightness of the LCD
display can be changed. Press [OK] to confirm.
LCD brightness in sleep mode.
Select [MENU] in the Normal display, [Service] and then [Display].
Highlight [Stand by (%)] and press the middle button. The highlighted text
then turns dark blue and the value for the brightness of the LCD display
when the panel is on stand-by can be changed. Press [OK] to confirm.
(The factory setting is 30%.)
Countdown to LCD sleep mode.
Select [MENU] in the Normal display, [Service] and then [Display].
Highlight [Stand by time] and press the middle button. The highlighted
text then turns dark blue, and you can reduce or extend the length of time
it takes before the LCD display dims after the panel has switched to
stand-by. Press [OK] to confirm.
Service.
See SERVICE SETTINGS
Code lock.
Select [MENU] in the Normal display and then [Service]. Use the arrow
keys to move to [Code lock] and press [OK]. Enter the desired code. Use
the arrow keys to display the correct combination and confirm with [OK].
The security code function is automatically activated during programming
and the panel shows Normal display.
CC 300T
To return to unlocked mode, repeat the above procedure and set the
code to 0000.
It is not possible to change any settings when the security function has
been activated. It is possible, however, to switch both the facility and the
lighting on and off. The bathing cycle runs for the time indicated in the
Service menu under [Time outside timer]. (Factory setting: 1 hour).
A general code that always works is 1995.
IMPORTANT! Program all settings before activating security code.
Language.
Select [MENU] in the Normal display and then [Service]. Select
language. Use the arrow keys to select the required language and then
press [OK].
Clock.
Select [MENU] in the Normal display and then [Service]. Select [Set
clock). First use the arrow keys to set the right day and confirm with [OK].
Then set the correct time; first the hour and then the minutes.
Factory settings.
Select [MENU] in the Normal display and then [Service]. Select [Factory
settings]. Use the arrow keys to select [Yes] or [No] and then press [OK].
Selecting [Yes] deletes all your own programmed settings and the panel
reverts to the original factory settings.
SERVICE SETTINGS
Service.
The Service menu enables the bathing facility attendant to change
certain settings such as the maximum bathing temperature. However, we
recommend that the original factory settings are always retained. The
Service menu is protected by a code to prevent unauthorised users from
changing factory settings. In the Normal display press [MENU] and then
[Service]. Select [Service] and enter the code 124.
System settings.
Limit for automatic drying cycle
[Dryup limit (%)] – When the facility switches off, it measures the relative
humidity in the room. If this exceeds 30% (factory setting), the equipment
initiates a drying cycle.
Drying temperature
[Dryup temperature (°C)] – The ambient temperature in the facility during
the drying cycle. Factory setting: 80°C.
Drying time
[Dryup time (mins.)] – The duration of the drying cycle. Factory setting:
20 minutes.
Minimum temperature for steam generation
[Min. temp. steam (°C)] – The lowest temperature at which the steam
generator starts. Factory setting: 40°C.
Maximum running time
[Max running time (hrs)] – The running time that was set at the initial
start-up. This setting does not apply when the equipment has been
programmed. Adjustable from 1–24 hrs. Factory setting: 3 hrs.
Temperature unit
[Temperature (°C/°F)] – This feature enables you to display temperatures
in Celsius or Fahrenheit.
Test menu
The Test menu is used only for trouble-shooting and technical support
via Tylö.
Max temperature.
[Max temp (°C/°F)] – Used to set the maximum temperature to which the
facility can be programmed.
Temperature reduction during stand-by.
[Temp reduction Stand by (°C/°F)] – This is where you indicate the
reduction in temperature from the programmed bathing temperature to
the stand-by temperature. Factory setting: 30°C.
Max. running time during stand-by.
[On time Stand by (mins)) – The duration of the bathing cycle that is
initiated when the ON button is pressed while the facility is on stand-by.
Factory setting: 60 minutes.
Max running time outside programmed time.
CC 300T
7