Important; General Characteristics - Astralpool LUMIPLUS MINI V3 Manuel D'installation Et D'entretien

ENGLISH
IMPORTANT: The instruction manual you are holding includes essential information on the safety measures to be im-
plemented for installation and start-up. Therefore, the installer as well as the user must read the instructions before
beginning installation and start-up.
Keep this manual for future reference.
To achieve optimum performance of the LumiPlus Mini V3 Spotlight, follow the instructions provided below:
1. VERIFY THE CONTENTS OF THE PACKING:
The following accessories are included inside the box:
• Unit spotlight
• 1" 1/2 adaptor
• Manual for electrical connection

2. GENERAL CHARACTERISTICS:

This spotlight has been designed to be used totally submerged in water. It is a Class III electric apparatus with very low
safety voltage (12 V AC - 24 V DMX with power pack, code 52142).
The spotlight compiles with IPX8 degree of protection (resistance to penetration of dust, solid bodies and humidity) at a
nominal immersion depth of 2 m.
This spotlight compiles with international safety standards for lights, especially the EN 60598-2-18 standard. LIGHTS
PART 2: SPECIFIC REQUIREMENTS SECTION 18 LIGHTS FOR SWIMMING POOLS AND SIMILAR APPLICATIONS.
The manufacturer is not responsible in any circumstances for assembly, installation or start-up of any electric components
which have been inserted or handled at locations other than its own premises.
3. INSTALLATION:
• To illuminate a pool properly, it is advisable:
To install a spotlight from the LumiPlus Mini V3 family for every 5m² of water surface. In particularly deep pools, it will be
necessary to install a spotlight for every 10 m³ of water.
Note: Strongly recommended for pools in light colors. In dark colored and stainless steel pools, we recommend increasing
the proportion of spotlights per m2.
• In order to avoid glare, the spotlights should be fitted so that they face the opposite direction to the home or any other
poolside building used as living quarters.
• Should lighting be used in competition or training pools, the spotlights should be fitted on the sides to avoid swimmers
being dazzled by the light.
• It is recommended that a length of cable be left in the niche or wall conduit that is approximately the same depth as the
spotlight fixture + 30 cm so that it can be pulled out up to the edge of the pool if it has to be handled (Fig. 1).
• The inside of the spotlight should not be handled under any circumstances, otherwise the warranty will no longer be valid.
• The spotlight is not watertight: if a LumiPlus Mini V3 is installed in ducts, conduits or bushings, a siphon must be fitted
to avoid emptying the pool (see Fig. 1).
The spotlight should be fitted 400–700 mm below the surface of the water on one of the pool walls (Fig. 1). The way the
spotlight is fitted will depend on whether bushing or piping is used.
• Should the cable have been replaced before installing the spotlight, check that the stuffing box is firmly tightened.
4. ASSEMBLY:
There are various ways of mounting a LumiPlus Mini V3:
Concrete pools
A) Directly on Ø63 PN-6/10 piping. (Fig. 2a)
Recess required: No/Accessories required: 62395/Siphon required: Yes
Procedure:
1 - A suitable O-ring seal must be selected to fit to the piping and to place it on the PN6 pipe adaptor: Ø53 x 3 O-ring seal
PN10 pipe: Ø53 x 2 O-ring seal
2 - Twist the adaptor into the piping.
3 - Insert the cable in the piping, ease the spotlight in and turn 90º clockwise (Fig. 5).
4 - Put the face plate into place with the logo facing the top of the fixture (Fig. 5).
B) On bushing with G1" 1/2 thread glued to Ø63 piping. (Fig. 2b1, 2b2)
Recess required: 35618 for Ø63 PN-06 piping/35412 for Ø63 PN-10 piping.
Accessories required: No/Siphon required: Yes
Procedure:
1 - Glue bushing in place that is suitable for the type of piping used.
2 - Screw in the adaptor included with the spotlight.
• Warranty booklet
• Installation and maintenance manual
• Spanner for adaptor
3