Sigel artverum Instructions De Montage Et De Sécurité page 3

GB MOUNTING INSTRUCTIONS
1 // Before mounting, check that there are no service pipes, e.g. for electricity, gas or water, in that part of the wall.
2 // When mounting the magnetic glass board, please ensure that it does not come into contact with sharp objects or hard surfaces such as stone
or tiles. We cannot accept any claims for resulting damage to the board. Place the board on a soft surface until it is ready to be mounted and do
not remove the protective corners until it is attached to the wall.
3 // The magnetic glass board should only be mounted on an even, solid wall.
4 // Two people are required to mount the board.
5 // In order to mount our magnetic glass boards correctly, we recommend using the enclosed drilling templates. The exact distances between the
drill holes can be found on page 6 and on our website at www.sigel.de/montage
MOUNTING INSTRUCTIONS FOR PROJECTION SCREEN MAGNETIC GLASS BOARDS GL 300 AND GL 301
6 // Ideal viewing height (minimum distance between the bottom of the projection screen and the floor): for professional use, at least 125 cm;
for home cinemas, at least 60-90 cm
7 // Minimum viewing distance: distance from the projection screen board to the first row of seats = height of the board x 1.5
MOUNTING
1 // The magnetic glass board can be mounted in portrait or landscape format. The enclosed drilling templates make it simple to mark the position
of the drill holes. The wall fixings
should be facing outwards (fig. I).
Tip: Please use a spirit level to check that the wall fixings
The wall fixings have an oblong hole that can be used to adjust their position if necessary. To do so, loosen the screw and move the wall fixings
vertically or horizontally as required. Then tighten the screw again.
2 // Two people are required to mount the magnetic glass board. A handle
Tip: to simplify the positioning of the board, mark the wall lightly in pencil (fig. II), e.g. to indicate the width of the board. Likewise, you can mark the
position of the corners and the mounting fittings (for distances see pg. 6).
To mount the board, use the handle
IV). The magnetic glass board
this. Each mounting fitting has two openings (fig. VI); the wall fixings
ning, whether the board is hung in portrait or landscape format. Place the mounting fittings
so that the wall fixings are in the centre (fig. VI). Now slide the board downwards so that the wall fixings
(fig. VII) and the board is mounted securely.
Make sure that the magnetic glass board is mounted on all six fittings and check that the board is securely in place before letting go. Silicon pads
on the back of the board keep it steady while it is being written on.
SAFETY PRECAUTIONS
The artverum® Magnetic Glass Board is made of tempered safety glass tested to EN 12150-1.
The glass surface should be written on using only special markers for glass. The magnetic glass board can be cleaned with a damp or dry cloth.
Please do not use abrasive scouring agents, detergents or chemicals to clean the board. To prolong the life of your board, we recommend using
our own Sigel accessories: liquid chalk markers and microfibre cloth.
Sigel GmbH does not assume any responsibility or guarantee for boards that have been incorrectly mounted or for any resulting damage.
25
GUARANTEE
*
J A H R E
* We offer a 25-year guarantee that the glass surface will remain perfect to write on and to clean. We guarantee that the
Y E A R
magnetic glass board will remain easy to wipe and free of smudges and other residue when using Sigel accessories and
G A R A N T I E
following our instructions for use. This guarantee does not apply in cases of mistreatment, negligence, incorrect usage or
AUF BOARDOBERFLÄCHE
G U A R A N T E E
other methods of utilisation that do not comply with the enclosed instructions.
F O R B O A R D S U R FA C E
TÜV-APPROVED
With TÜV-approved safety mounting fittings plus superb function and product quality - tested and approved by the Global
Safety Certification of the TÜV Saar branch (usability).
MAGNETS
For attaching notes, postcards, etc, use the enclosed SuperDym magnets or magnets with an extra-strong hold. Treat the SuperDym
magnets with caution at all times and separate them by sliding them apart sideways. Please ensure that there is a distance of at least
5 cm between the individual magnets (GL 195, GL 196, GL 197) on the artverum® Magnetic Glass Board. If used incorrectly, two or more
magnets may collide unexpectedly, causing the magnets to splinter and the magnetic coating to chip. Splinters can fly off the magnet,
injuring people nearby and damaging the glass surface of the board. Careless use can lead to fingers or skin becoming jammed between
two magnets, resulting in bruising. Magnets create a strong, far-reaching magnetic field. Among other things, they can cause damage to
televisions, laptops, computer hard drives, credit cards and EC cards, data carriers, mechanical watches, hearing aids and loudspeakers.
Magnets can affect the functioning of pacemakers and heart defibrillator implants. Magnets are not toys! Keep them away from children
– small parts are a choking hazard. Make sure that the magnets are kept out of the reach of children. Sigel cannot be held liable for any
damage or injury caused by a failure to follow these safety measures.
are screwed securely to the wall using anchors
are lined up straight.
to hold the lower edge of the board (fig. III) while holding the side of the board with your other hand (fig.
is then mounted onto the wall fixings
and screws
is provided for each person.
(fig. V). There are six mounting fittings
must always be slotted into the top opening rather than the side ope-
on the back of the board over the wall fixings
3
. The side of the board with the Sigel logo
on the back of the board for
click into the mounting fittings