Trevi TT 1068 E Mode D'emploi Et Connexion page 13

ENGLISH
3. Press the rec button, it will take 3-5 seconds to read memory device. Then usb or sd icon will be flashing.
4. Turning skip up or skip down knob to select desired mode (usb or sd) for encoding. Then press the rec button again to confirm. And the system
is starting the encoding mode after few secondss.
5. If only usb drive, sd or mmc card is inserted, step 4 can be skipped.
6. The usb or sd icon will be flashing on the display durnig encoding.
7. To finish encoding, press stop button and display will show "end" and return to " tuner" mode.
Remark:-
-The recording speed is 1:1 and according to the actual playing time of fm or fm-st radio
-The recording format is preset at – mp3 bit rate : 128 kbps
-During fm & fm-stereo radio encoding, radio freqeuncy is fxied and cannot be tuned
Phono & Encoding
Noted:
-Remove the stylus protector.
-Be sure that the tone arm is being detached from the tone arm rest before operating and re-secured again afterwards.
1. Press Phono button to select "phon" on display.
2. Set the speed selector to the proper position depending on the record to be played.
3. Place the record on the platter, use the 45 rpm adaptor if required.
4. Push the lift lever upward to raise the tone arm from the arm park, and then slowly move it to the record side. The platter will start to rotate.
5. Put down the lift lever to drop the tone arm and touch the record gently. Phono playing starts now.
6. Push the lift lever upward to raise the tone arm from the arm park, now platter will still be rotating but phono playing will stop. To continue the
playing, the user needs to put down the lift lever.
7. Adjust the volume to the desired level.
8. At the end of record, the platter will automatically stop rotating. Push the lift lever upward to raise the tone arm and move it to the arm park, and
then put down the lift lever.
9. To stop manually, lift the tone arm from the record and return it to the arm park.
Remark : as some kind of record the auto-stop area was out of the unit setting, so it will stop before the last track finishes. In this case, select
the auto-stop switch to " off " position, then it will run to the end of the record but will not stop automatically (turn off the unit by power button
or switch back the auto-stop switch to " on " position to stop the platter rotate). Then put back the tone arm to the arm park.
Phono Encoding
1. Press phono button to activate "phon" on display and then insert memory device (usb drive, sd or mmc card).
2.Press the rec button, it will take 3-5 seconds to read memory device. Then usb or sd icon will be flashing.
3.Turning skip up or skip down knob to select desired mode (usb or sd) for encoding. Then press the rec button again to confirm. And the system
is starting the encoding mode after few secondss.
4. If only usb drive or sd/mmc card is inserted, step 3 can be skipped.
5.The usb or sd icon will be flashing on the display durnig encoding.
6.To finish encoding, press stop button and display will show "end" and return to phono mode.
Remark:-
-The recording speed is 1:1 and according to the actual plying time of the phono
-The recording format is preset at – mp3 bit rate : 128 kbps
Aux In Jack & Encoding
Press aux button to activate "aux" on display, then connect the external audio device (such as cd player) through the aux in jack. Audio signal from
the external audio device can be played through the system.
Aux In Encoding
1. Press function button to select "aux" on display, then insert memory device (usb drive, sd or mmc card)
2.Press the rec button, it will take 3-5 secondss to read memory device. Then usb or sd icon will be flashing.
3.Turning skip up or skip down knob to select desired mode (usb or sd) for encoding. Then press the rec button again to confirm. And the system
is starting the encoding mode after few secondss.
4.If only usb drive or sd/mmc card is inserted, step 3 can be skipped.
5.The usb or sd icon will be flashing on the display durnig encoding.
6.To finish encoding, press stop button and display will show "end" and return to "aux" mode.
Remark:-
-The recording speed is 1:1 and according to the actual plying time of the external audio device.
-The recording format is preset at – mp3 bit rate : 128 kbps
Playback Of Mp3/Wma Song Via Usb Storage Media Or Memory Card
The system is able to decode and playback all mp3 / wma file which stored in the memory media with usb connecting port or sd/mmc memory card.
1. Plug-in the usb plug with the face up & make sure it going into completely or insert the memory card in the direction of the arrow as shown in
the label on the underside of the memory card slot cover. Insert straight without bending.
2. Connecting the usb upside down or backwards could damage the audio system or the storage media (usb thumb drive / sd/mmc card). Check
to be sure the direction is correct before connection.
3. Press cd/usb/sd button to select "usb" or "card" on display, then insert memory device (usb drive, sd or mmc card).
4. The system will start reading the storage media automatically after function selection, and display will show the total number of mp3/wma files
(eg. 016).
5. Then the system will start audio playback from desried device (usb or sd/mmc) automatically.
TT 1068 E
13