Warning; State-Of-The-Art Features; Electrical / Motor Specifications; Unpacking, Assembly & Setup - QEP 60007 Manuel D'utilisation Et Liste De Pièces

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

ENGLISH

WARNING

FOR YOUR OWN SAFETY READ INSTRUCTION MANUAL BEFORE OPERATING SAW.
• Wear eye protection.
• Use splash hood for every operation for which it can be used.
• Disconnect saw before servicing, when changing cutting wheels, and cleaning.
• Use tool only with smooth-edge cutting wheels free of openings and grooves.
• Replace damaged cutting wheel before operating.
• Do not fill water bath above water fill line.
USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be
sure to use a cord heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line
voltage, resulting in loss power and overheating. Table below shows the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
MINIMUM GAUGE FOR CORD
TOTAL LENGTH OF CORD IN FEET

STATE-OF-THE-ART FEATURES

1
-HP motor, 4,000 RPM
2
• Automatic thermal overload protection protects saw
from power surges and motor overheating.
• Specially designed mounting provides easy blade
change.
• Fiberglass-impregnated plastic water tray withstands
even the toughest punishment. Easy to remove and
install.
• The adjustable rip guide allows both 90° and 45° cuts.
• Rip cut up to 16" square tiles and diagonal cut up to
10" tiles.
• Easily removable for cleaning and transportation.
• Lightweight for easy setup and maintenance.
UNPACKING, ASSEMBLY & SETUP
CAUTION: FOLLOW ALL OF THE ASSEMBLY & INSTALLATION INSTRUCTIONS COMPLETELY BEFORE CONNECTING THE
SAW TO A POWER SOURCE OR TURNING THE MOTOR ON.
Carefully open the container and remove all saw components and packing materials. Ensure that you have checked each
item with the exploded view on Page ?? before discarding the container or packing materials. The contents of the
container are as follows:
• Cutting Head Assembly
• Close Wrench
• Owner's Manual
The following pages illustrate step by step the installation of various components and operation of the saw. Read
instructions completely before operating this saw!
CUTTING-HEAD ASSEMBLY INSTALLATION
CAUTION: FOLLOW ALL OF THE ASSEMBLY & INSTALLATION INSTRUCTIONS
COMPLETELY BEFORE CONNECTING THE SAW TO A POWER SOURCE OR TURNING THE
MOTOR ON.
1. Remove the motor mount block and motor from the packaging, loosen the wing
screws enough to permit the motor mount to fit on the frame upright post.
2. Set the motor mount block on the frame upright post, then tighten the 2 wing
screws to hold the motor block securely in place. (Diagram 1)
18 AWG
25
• 45° / 90° Rip Guide
• 7" Saw Blade
• Blade Guard Accessory
16 AWG
16 AWG
50
100

ELECTRICAL / MOTOR SPECIFICATIONS

• Horsepower
1
2
• Volts
115V
• Amps
5.8
• RPM
4,000
• Cycle
60
• Phase
1
• Connect saw as close as possible to power source.
EXTENSION CORDS: When using an extension cord,
ensure all cords are no smaller than #12 gauge, rated at
a 20 AMP minimum, and equipped with 3-prong plugs.
Use of anything smaller may result in overheating or
burn out of the motor. It is recommended to have an
electrician check the voltage at the saw motor to ensure
proper voltage to run the saw efficiently and safely.
• Water Pump
• Fiberglass-Impregnated Plastic Water Tray
- 5 -
14 AWG
150
H.P. Saw-duty rated
• Saw-Frame Assembly

Publicité

Table des Matières
loading

Table des Matières