Kenwood KDC-X704 Mode D'emploi page 37

Audio Settings
[X ' OVER]
[TWEETER] [FRQ]
[GAIN LEFT]
[GAIN RIGHT]
[FRONT HPF] [F-HPF FRQ]
[F-HPF SLOPE]
[F-HPF GAIN]
[REAR HPF] [R-HPF FRQ]
[R-HPF SLOPE]
[R-HPF GAIN]
[SUBWOOFER LPF] [SW LPF FRQ]
[1KHZ]/[1.6KHZ]/[2.5KHZ]/[4KHZ]/[5KHZ]/
[6.3KHZ]/[8KHZ]/[10KHZ]/[12.5KHZ]: Adjusts the
crossover frequency for the tweeter speaker.
[–8] to [0]: Adjusts the output volume of the left
tweeter.
[–8] to [0]: Adjusts the output volume of the right
tweeter.
[30HZ]/[40HZ]/[50HZ]/[60HZ]/[70HZ]/[80HZ]/
[90HZ]/[100HZ]/[120HZ]/[150HZ]/[180HZ]/
[220HZ]/[250HZ]: Adjusts the crossover frequency
for the selected speakers (high pass filter). ;
[THROUGH]: All signals are sent to the selected
speakers.
[–6DB]/[–12DB]/[–18DB]/[–24DB]: Adjusts the
crossover slope.
(Selectable only if a setting other than [THROUGH] is
selected for [F - HPF FRQ].)
[–8] to [0]: Adjusts the output volume of the
selected speaker.
Configure the settings for the rear speakers similarly
to the front speakers.
[30HZ]/[40HZ]/[50HZ]/[60HZ]/[70HZ]/[80HZ]/
[90HZ]/[100HZ]/[120HZ]/[150HZ]/[180HZ]/
[220HZ]/[250HZ]: Adjusts the crossover frequency
for the subwoofer (low pass filter). ; [THROUGH]: All
signals are sent to the subwoofer.
[SW LPF SLOPE] [–6DB]/[–12DB]/[–18DB]/[–24DB]: Adjusts the
[SW LPF
PHASE]
[SW LPF GAIN]
[DTA SETTINGS]
For settings, see "Digital Time Alignment settings" on page 32.
[CAR SETTINGS]
• (For /
The following item is selectable only if [SWITCH PREOUT] is set to [SUB-W]
(page 6):
– [SUB-W LEVEL]
– [SUBWOOFER SET]
– [SW LEVEL] of [EASY EQ]
– [SUBWOOFER] of [SPEAKER SIZE]
– [SUBWOOFER LPF] of [X ' OVER]
– [SUBWOOFER] of [DISTANCE] and [GAIN] in [DTA SETTINGS]
• The following item is selectable only if [SUBWOOFER SET] is set to [ON]
(page 30):
– [SUB-W LEVEL]
– [SW LEVEL] of [EASY EQ]
– [SUBWOOFER] of [SPEAKER SIZE]
– [SUBWOOFER LPF] of [X ' OVER]
– [SUBWOOFER] of [DISTANCE] and [GAIN] in [DTA SETTINGS]
• The following item is selectable only if a setting other than [NONE] is
selected for [TWEETER], [REAR] and [SUBWOOFER] of [SPEAKER SIZE]:
– [TWEETER], [REAR HPF], [SUBWOOFER LPF] of [X ' OVER]
crossover slope.
(Selectable only if a setting other than [THROUGH] is
selected for [SW LPF FRQ].)
[REVERSE] (180°)/[NORMAL] (0°): Selects the
phase of the subwoofer output to be in line with the
speaker output for optimum performance.
[–8] to [0]: Adjusts the output volume of the
subwoofer.
/ )
ENGLISH
31