Yamaha HTR-6230 Mode D'emploi page 20

The "BASIC SETUP" feature is a useful way to set up
your system quickly and with minimal effort.
Notes
• Make sure that you disconnect your headphones from this unit.
• If you wish to configure this unit manually using more precise
adjustments, use the detailed parameters in "SOUND MENU" (see
page 32).
• Altering any parameters in "BASIC SETUP" resets all parameters
manually adjusted in "SOUND MENU" (see page 32).
• Initial settings are indicated by (*) in the following each parameters.
• Press nRETURN on the remote control to return to the previous menu
level.
1
Press hAMP on the remote control.
2
Press kMENU.
"BASIC SETUP" appears on the front panel display.
3
Press lENTER to enter "BASIC SETUP."
"ROOM: S M L" appears on the front panel display.
4
Press ll / h to select the desired setting.
Select the size of the room where you have installed
your speakers. The room sizes are defined as follows:
Choice Approximate Size of the room
S
16 x 13 ft, 200 ft
M*
20 x 16 ft, 300 ft
L
26 x 19 ft, 450 ft
5
Press ln to select "SUBWOOFER" and then
ll / h to select the desired setting.
"SUBWOOFER" and the current setting appear on
the front panel display.
Choice
YES*
When you have a subwoofer in your system.
NONE
When you do not have a subwoofer in your
system.
6
Press ln to select "SPEAKERS" and then
ll / h to select the number of speakers
connected to this unit.
"SPEAKERS" and the current setting appear on the
front panel display.
Choice Display
2spk
L R
3spk
L C R
4spk
L R
SL SR
5spk*
L C R
SL SR
7
Press ln to select "SET" and then ll / h
to select the desired settings.
"SET" and "CANCEL" appear on the front panel
display.
16
En
Basic setup
2 2
(4.8 x 4.0 m, 20 m )
2 2
(6.3 x 5.0 m, 30 m )
2 2
(7.9 x 5.8 m, 45 m )
Condition
Speakers
Front L/R
Front L/R Center
Front L/R, Surround L/R
Front L/R, Center, Surround L/R
Choice
SET
Applies the settings you made.
CANCEL*
Cancels the setup procedure without making
any changes.
y
• You can also press kMENU to cancel the setup procedure.
8
Press lENTER to confirm your selection.
If you selected "SET" in step 7, each speaker outputs
a test tone twice in turn. "CHECK:TestTone" appears
on the front panel display for a few seconds and then
"CHECK OK?" appears on the front panel display.
y
• Check the speaker connections (see page 9) and adjust the
"SPEAKERS" settings back in step 6, if necessary.
• The indicator of the speaker currently outputting the test tone
flashes on the front panel display.
9
Press ll / h to select the desired settings.
Choice
YES*
Completes the setup procedure if the test tone
levels from each speaker were satisfactory.
NO
Proceeds to the speaker level adjustment menu
to balance the output level of each speaker.
10
Press lENTER to confirm your selection.
• If you selected "YES" in step 9, the setup
procedure is completed and then display returns to
the top set menu display. Press kMENU to exit
from "BASIC SETUP."
• If you selected "NO" in step 9, the front speaker
level adjustment display appears on the front panel
display.
11
Press lk / n to select a speaker and then
ll / h to adjust the balance.
The selected speaker and the front left speaker (or the
surround left speaker) output a test tone in turn.
• Press lh to increase the value.
• Press ll to decrease the value.
■
The balance between speakers you can
adjust in each item is defined as follows.
Choice Adjusted balance between speakers
FR
the front left and right speakers
C
the front left and center speakers
SL
the front left and surround left speakers
SR
the surround left and surround right speakers
SWFR
the front left speaker and the subwoofer
Note
• The available speaker channels differ depending on the setting of the
speakers.
12
Press kMENU to exit from "BASIC SETUP."
Function
Function