Troubleshooting; Power Indicator Is Not Illuminated; Fuse Replacement; No Sound - Rotel DT-6000 Manuel De L'utilisateur

16

Troubleshooting

Most difficulties in audio systems are the result of incorrect connections, or
improper control settings. If you encounter problems, isolate the area of the
difficulty, check the control settings, determine the cause of the fault and
make the necessary changes. If you are unable to get sound from the unit,
refer to the suggestions for the following conditions:

Power Indicator Is Not Illuminated

The Power Indicator and the basic items in the display window should be
illuminated whenever the unit is plugged into the wall power outlet and the
Power button is pushed in. If it does not light, test the power outlet with
another electrical device, such as a lamp. Be sure the power outlet being
used is not controlled by a switch that has been turned off.

Fuse Replacement

If another electrical device works when plugged into the power outlet,
but the Power Indicator and the display still will not light when the unit is
plugged into the wall outlet, it indicates that the internal power fuse may
have blown. If you believe this has happened, contact your authorized Rotel
dealer to get the fuse replaced.

No Sound

Check the cables between the unit and the amplifier inputs to be sure they
are connected properly. Be sure the correct amplifier input is selected. Be
sure the tape monitor system of the amplifier has not been activated. Check
the wiring between the amplifier and the speakers.

Playable Audio Formats

PC-USB
Format
Any supported format by the PC software
PCM Audio:
Format determined
44.1k, 48k, 88.2k, 96k, 176.4k, 192k, 384k
by the Media Player/
(16 bit, 24 bit and 32 bit)
Server software that
DSD64, DSD128 and DSD256
you use.
MQA, MQA Studio (24 bit / 384k)
Roon Tested
Coax/Optical
Format
44.1k, 48k, 88.2k, 96k, 176.4k, 192k
SPDIF LPCM
16 bit, 24 bit
Notes
Notes

Specifications

Total Harmonic Distortion + Noise Total Harmonic Distortion + Noise
Optical/Coaxical Input
CD/PC-USB Input
Intermodulation Distortion Intermodulation Distortion
Frequency Response Frequency Response
Channel Balance Channel Balance
Channel Separation Channel Separation
Signal to Noise Ratio (A Weighting) Signal to Noise Ratio
Dynamic Range Dynamic Range
Input Sensitivity Input Sensitivity
Digital to Analog Converters Digital to Analog Converters
Analog Output Level / Impedance (0dBfs) Analog Output Level / Impedance
Unbalanced (RCA)
Balanced (XLR)
Decodable Coaxial/Optical Digital Signals Decodable Coaxial/Optical Digital Signals
Decodable PC-USB Digital Input Signals Decodable PC-USB Digital Input Signals
Power Requirements Power Requirements
USA
EC
Power Consumption Power Consumption
Standby Power Consumption Standby Power Consumption
Dimensions Dimensions
(W x H x D)
Front Panel Height Front Panel Height
Weight Weight
(net)
All specifications are accurate at the time of printing. Rotel reserves the right to make
improvements without notice.
Rotel and the Rotel HiFi logo are registered trademarks of The Rotel Co, Ltd., Tokyo, Japan.
DT-6000 DAC Transport
< 0.0007%
< 0.0012%
< 0.0012%
20 Hz - 20k Hz，+0, -0.15 dB
10 Hz - 70k Hz, +0, -3 dB
± 0.5 dB
> 115 dB @ 10k Hz
> 115 dB
> 99 dB
0dBfs / 75 Ohms
ESS 32 Bit/768kHz DAC
2.1 V / 10 Ohms
4.3 V / 20 Ohms
SPDIF LPCM (up to 24 bit/192k Hz)
USB Audio Class 2.0
(up to 32 bit/384k Hz)
*Driver installation required*
Support native DSD (up to 11.2M)
and DoP
Support MQA and MQA Studio
(up to 24 bits/384kHz)
Roon Tested.
120V, 60 Hz
230V, 50 Hz
25 Watts
< 0.5 Watts
431 x 104 x 320 mm
17 x 4 x 12 3 / ins
5
2U / 3 1 / ins / 88.1 mm
2
8.11 kg, 17.88 lbs.