Operation; Dimming Dmx First Address Setting; Dimming Control Output Mode Setting; Change Of Settings Via Rdm Dimming - Leviton LWCYC-00B Mode D'emploi

OPERATION

LWCYC-00B can be put into service after installation and cable connection.
When power is applied, the LWCYC-00B will be in controllable state after a self-check process. The PWR LED indicator
on the control panel will be ON. The LED display will display the dimming DMX first address (for example: A001), and
when there is DMX512/RDM signal input, the SIG LED indicator will be ON. Within 30 seconds after start, if no operation is
performed on the function setting knob, the LED display will be automatically turned OFF. After the turn-off of display, any
operation on function setting knob will re-activate the display. Similarly, within 30 seconds after re-activation of the display, if
no operation is performed on the function setting knob, the LED display will be automatically turned OFF again.

DIMMING DMX FIRST ADDRESS SETTING

By default, dimming DMX first address of LWCYC-00B is set to 1. Users can change this address setting accordingly. The dimming
DMX first address can be directly changed by the function setting knob on the control panel or remotely modified via RDM.
The following describes the procedure of changing dimming DMX first address by the function setting knob on the control panel:
When the LED display is displaying the dimming DMX first address, press the setting knob, then the display content will be
switched to ADD-. Turn the setting knob at this time. The display content will be switched between SET- and ADD-.
If the setting knob is pressed again when the LED display is displaying ADD-, the display content will be switched to
AX.X.X. (where XXX is current address content of LWCYC-00B). At this time, if the setting knob is turned clockwise
(counterclockwise), the address will increase (decrease). After the setting knob is turned to the desired address, press the
setting knob to complete the change of dimming DMX first address setting. The display content will be switched back to
dimming DMX first address display. LWCYC-00B will automatically save the changed dimming DMX first address. This setting
will not be lost even if LWCYC-00B is turned OFF.

DIMMING CONTROL OUTPUT MODE SETTING

Dimming control output mode of LWCYC-00B is set to 4COL by default. Users can change this dimming control output mode
setting accordingly. The dimming control output mode can be directly changed by the function setting knob on the control
panel or remotely modified via RDM.
The following describes the procedure of changing dimming control output mode by the function setting knob on the control panel:
When the LED display is displaying the dimming DMX first address, press the setting knob, then the display content will be
switched to ADD-. Turn the setting knob at this time. The display content will be switched between SET- and ADD-.
If the setting knob is pressed again when the LED display is displaying SET-, the display content will be switched to 4COL,
HIS, FIL or CCT (dependent on the current actual situation). At this time, if the setting knob is turned, the display content will
be switched among the above mentioned 4 settings and the switching direction is dependent on the turning direction of the
setting knob. After the setting knob is turned to the desired setting, press the setting knob to complete the change of dimming
control output mode setting. The display content will be switched back to dimming DMX first address display. LWCYC-00B will
automatically save the changed dimming control output mode. This setting will not be lost even if LWCYC-00B is turned OFF.
NOTE: During the procedure of changing the dimming DMX first address or dimming control output mode setting, if the
setting knob is not pressed to confirm the change, LWCYC-00B will keep the original setting.

CHANGE OF SETTINGS VIA RDM DIMMING

DMX first address setting of LWCYC-00B can be changed through RDM_DMX_START_ ADDRESS. Dimming control output
mode setting of LWCYC-00B can be changed through RDM_DMX_PERSONALITY. The correspondence between the
dimming control output mode and DMX_PERSONALITY codes are as shown in the following table.
Dimming Control Output Mode
LWCYC-00B can simultaneously change the dimming DMX first address and dimming control output mode to the factory
settings via RDM_FACTORY_DEFAULTS.
DMX_PERSONALITY Code
4COL
HSI
FIL
CCT
5
1
2
3
4