Communication Cable Connection; Dimming Control Output Mode - Leviton LWCYC-00B Mode D'emploi

COMMUNICATION CABLE CONNECTION

DMX512 signal enters LWCYC-00B via input 5-pin XLR male on the control panel and can be connected to the next set of
LWCYC-00B cyclorama lights or other DMX devices via the output 5-pin XLR female socket.
NOTE: When DMX512 passes through input and output connection transmission of multiple LWCYC-00B cyclorama lights
or other DMX devices, the total number of these devices must not exceed 32 sets and the cumulative transmission distance
should not exceed 984' (300 m). A 5-pin XLR male with terminal resistance should be plugged on the output 5-pin XLR
female socket of LWCYC-00B or other DMX device at the tail of the signal transmission. When the number of LWCYC-00B
cyclorama lights or DMX devices exceeds 32 or DMX512 signal transmission distance is longer than 984' (300 m), use a
DMX signal distributor to meet the signal transmission requirement.
XLR Pin No. Definition
1 Common Terminal
2 Signal -
3 Signal +
4
5

DIMMING CONTROL OUTPUT MODE

The light source of LWCYC-00B is composed of 32 LED lamp beads, and each lamp bead contains light emitting bodies of
four colors - red (R), green (G), blue (B) and white (W). Based on the light output control modes of light source, LWCYC-00B
can provide four different dimming control output modes.
• 4COL (Red, Green, Blue, White)
This is a traditional dimming control output model to control brightness and color change. LWCYC-00B uses 4 successive
DMX512 channels to respectively control the output illumination of red, green, blue and white light sources, and completes
the color mixing by regulating the different proportions of various light sources to change the output brightness and color.
• HSI (Hue, Saturation, Intensity)
LWCYC-00B uses 3 successive DMX512 channels to control the output brightness, hue and saturation. During the
dimming output process, the DMX control values of these three channels all affect the output proportions of the four light
sources while outputting.
• FIL (Built-in color macros, Filters codes as color reference only)
LWCYC-00B has a built-in 16-color color changer for colored paper effect output, which is easier to operate than an
ordinary color changer. LWCYC-00B uses 2 successive DMX512 channels to respectively control the output brightness
and to select colored paper effect codes. With the following table, you can quickly query DMX value ranges that
correspond to 16 colored paper effect codes.
Effect DMX
Color
Code Value
1 0-15 Transparent
2 16-31 Pale gold
3 32-47 Straw yellow
4 48-63 Light amber
5 64-79 Chrome orange
6 80-95 Hot pink
7 96-111 Shocking pink
8 112-127 Magenta
NOTE: In terms of color, the light output by 4 colors of LEDs after color mixing will be different from the light emitted from
ordinary incandescent light and projected by color optical filter, and the colored paper codes in the above table are for
reference only.
• CCT (Color temperature for white lights)
LWCYC-00B can achieve white light output in four different color temperature
grades (3200K/4300K/5600K/6500K). LWCYC-00B uses 2 successive
DMX512 channels to respectively control the output brightness and to select
color temperature grades. With the following table, you can quickly find out the
DMX value ranges corresponding to the 4 color temperature grades.
Input (male)
XLR 5-pin
----
----
Colored Paper
Code
130
152
103
176
179
128
192
113
4
Output (female)
1 5
2 3 4
Effect DMX
Color
Code Value
9 128-143 Bright red
10 144-159 Rose purple
11 160-175 Light purple
12 176-191 Moss green
13 192-207 Dark green
14 208-223 Primary blue
15 224-239 Peacock blue
16 240-255 Dark blue
Color Temperature
Grade
3200K
4300K
5600K
6500K
XLR 5-pin
5 1
4 3 2
Colored Paper
Code
26
48
126
89
124
201
115
119
DMX Value
Range
0-63
64-127
128-191
192-255