Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
INTRODUCTION
Connect Internet
The CAPAC can connect to the Internet with a wired Ethernet, with Wi-Fi
configure which of the methods is used.
INTRODUCTION
Step 1
The CAPAC can connect to the Internet with a wired Ethernet, with Wi-Fi
(wireless) or with a cellular network. Log into the CAPAC Wi-Fi to configure
which of the methods is used.
1.
Press and hold the Reset/Learn button for 5 seconds to reset to factory
settings (the connectivity LED will be off).
2.
Press and hold the Reset/Learn button for 2 seconds to get to the access
point page (the connectivity LED will blink green).
3.
On your mobile device, go into Wi-Fi configuration and look for the CAPAC
Wi-Fi network. The Wi-Fi network format will be "MyQ-xxx" where xxx is
the last three digits of your CAPAC's CP#.
4.
If "Internet may not be available" message is received, select "keep Wi-Fi
connection".
5.
Open web browser (e.g., Edge, Chrome) and enter either
setup.myqdevice.com or 192.168.1.1. Note that if you exit the
CAPAC MyQ-xxx Wi-Fi network, open a new web browser and enter
setup.myqdevice.com or 192.168.1.1 to restart your configuration.
6.
Select Start to see the current Internet connection method.
Step 2
Ethernet (DHCP and Static)
The Local Area Network(LAN) port is a 10/100 Ethernet interface with an RJ45
jack for connecting the CAPAC to an Ethernet hub, switch, or router in order for
it to gain connectivity to the Internet. Use a straight (i.e. non-crossover) Cat5,
Cat5e, or Cat6 cable to connect to a local hub, switch or router. This type of cable
is referred to as an Ethernet cable in this manual.
1.
Connect an Ethernet cable from the Ethernet hub, switch or router to the Ethernet port of the CAPAC.
2.
For DHCP, select Ethernet DHCP and click on "Next" icon.
3.
For Static, select Ethernet Static and click on "Next" icon. Then fill in the information and click on "Next" icon.
4.
If the green LED next to the blue power LED is not lit or if the phone is still on the "connecting to Internet" screen after
3 minutes, check the connections on CAPAC and Ethernet hub. Resolve and repeat from Step 1.
5.
When connected properly, there will be a congratulation message indicating that your device is connected. The green
LED next to the blue power LED will be solid on the CAPAC housing.
6.
From your mobile device, exit the MyQ-xxx Wi-Fi network.
Wi-Fi
(Wireless)
®
1.
Select Wi-Fi and click on "Next" icon.
2.
Select your site's Wi-Fi network.
3.
Enter you Wi-Fi network password and then click on "Next" icon.
4.
Click "Next" icon again to acknowledge update.
5.
Select the status of the LED next to the blue power LED.
6.
When connected properly, there will be a congratulation message indicating that your device is connected. The green LED next to the blue power LED will
be solid on the CAPAC housing. Follow directions to troubleshoot issue if needed.
7.
From your mobile device, exit the MyQ-xxx Wi-Fi network.
Cellular (Wireless)
1.
Select Cellular and click on "Next" icon.
2.
From myQ
Business™, verify that the cellular service has been enabled for the CAPAC device. Note that this can take up to 15 minutes.
®
3.
When connected properly, there will be a congratulation message indicating that your device is connected. The green LED next to the blue power LED will
be solid on the CAPAC housing. Follow directions to troubleshoot issue if needed.
4.
From your mobile device, exit the MyQ-xxx Wi-Fi network.
PRE-INSTALL
PRE-INSTALL
INSTALL
NETWORK
(wireless), or with a cellular network. Log into the CAPAC Wi-Fi to
®
INSTALL
NETWORK
®
OUTPUT
1
OUTPUT
GATE
SDA SCL
NO COM NC
15
ACCESS CONTROL
ACCESS CONTROL
WIEGAND
INPUT
2
1
WIEGAND
2
INPUT
POWER
NO COM NC
D1 COM D0
D1 COM D0
1 GND 2
GND 12V-24V
Router/Switch
POWER
ETHERNET
Publicité
Chapitres
Table des Matières
