Positioning The Magnetic Temperature Probe - Timken VHIN 10 Mode D'emploi

Heater On 20 mm 30 mm
Series Supports (0.8 in) (1.2 in)
35 kg 5 kg
VHIS 35
(77 lb) (11 lb) (22 lb)
75 kg 10 kg
VHIS 75
(165 lb) (22 lb) (33 lb)
125 kg 10 kg
VHIS 100
(276 lb) (22 lb) (33 lb)
250 kg 10 kg
VHIS 200
(551 lb) (22 lb) (44 lb)
350 kg 10 kg
VHIS 150
(772 lb) (22 lb) (44 lb)
550 kg
VHIS 400 n/a
(1213 lb)
• To avoid the heater from tipping and damage to the yokes
and the hinge construction, the maximum weight for each
size yoke is restricted.
• Parts with a higher weight can rest on the horizontal supports
(if fitted), or be supported by a non-metallic rope from a crane,
avoiding any weight on the yoke.
Note: Not all ropes have the capacity for temperatures exceeding
100º C and those could possibly pose a safety hazard under
repeated use.
Diagram showing how the work piece can be supported:
VHIS 35, VHIS 75, VHIS 100 & VHIS150
VHIS 200, VHIS 400
Failure to observe the following cautions could
create a risk of injury.
• Always treat the yokes carefully. They can easily be
damaged through dropping, jolting etc. Always store the
yokes immediately after use.
Swing Arm Yoke Size
40 mm 50 mm 60 mm
(1.6 in) (2.0 in) (2.4 in)
10 kg 15 kg 20 kg 25 kg
(22 lb) (44 lb) (55 lb)
15 kg 25 kg 40 kg 45 kg
(55 lb) (88 lb) (99 lb)
15 kg 25 kg 40 kg
n/a
(55 lb) (88 lb)
20 kg 30 kg 60 kg
n/a
(66 lb) (132 lb)
20 kg 30 kg 60 kg
n/a
(66 lb) (132 lb)
30 kg 60 kg
n/a n/a
(66 lb) (132 lb)
CAUTION
6.
70 mm 80 mm
(2.8 in) (3.2 in)
n/a n/a
• Always use magnetic temperature
probe (hereafter referred to as
n/a n/a
the 'probe') for heating in the
50 kg
Temperature Mode.
n/a
(110 lb)
• The probe can be used as a
80 kg
n/a
(176 lb)
temperature-control aid for heating
80 kg
in the Time Mode.
n/a
(176 lb)
• The probe is suitable for operation
80 kg
n/a
(176 lb)
up to a maximum temperature of
240º C (464º F) - special probes are
supplied with custom machines
designed to operate above this
temperature.
• As a safety feature, the connection
between
will break above the maximum
temperature. If this occurs when
operating in the Temperature Mode,
the machine will turn itself off since
the probe will fail to register any
increase in the temperature over a
set period of time.
• A probe fixed to a clamp is also
available when heating non-magnetic work pieces.
• Ensure that the area where the probe is located is completely
clean.
• Always place the probe as close as possible to the bore of
the work piece (see opposite).
• Connect the probe by inserting the plug into the socket
at the back of the heater (the terminals have a different
orientation, so that the plug will only fit in one way.
Failure to observe the following cautions could
• Treat the probe with care. It is a valuable part of the
heater and can easily be broken through careless
handling. Place in a secure position after use.
7
Positioning the Magnetic
Temperature Probe
magnet and probe
CAUTION
create a risk of injury.
Correct
Incorrect