Cleaner Maintenance; Using Your Cleaner - Hoover SO60PAR Manuel D'utilisation

GETTING TO kNOw yOUR ClEANER
A. Main Cleaner
B. Cord Rewind Button
C. On / Off / Power Control Button*
D. Bag Check Indicator
E. Bag Door Release Latch
F. Bag Door
G. Hose Handle
H. Carry Handle
I. Dust Bag
J. Telescopic Tube
K. Telescopic tube adjuster
L. Hose
ASSEmBlING yOUR ClEANER
Remove all components from the packaging.
1. Connect the hose to the cleaner bag door, ensuring it clips and locks into position. To
release: simply press the two buttons on the hose end and pull. [1]
2. Connect the hose handle to the tube upper end. [2]
3. Connect the tube lower end to the nozzle. [3]

USING yOUR ClEANER

1. Extract the power cord and plug it into the power supply. Do not pull the cord beyond
the red marker. [4]
2. Adjust the length of the telescopic tube by moving the telescopic release button up and
raise or lower the hose handle to the most comfortable cleaning position. [5]
3. Carpet & Floor Nozzle**: press the pedal on the nozzle [6] to select the ideal celaning
mode according to the floor type
Hard Floor: The brushes are lowered to protect the floor
Carpet: The brushes are lifted for a deeper cleaning
4. switch the cleaner on by pressing the On/Off button on the cleaner main body. [7]
5. Fixed Power control* - The cleaner will operate at a fixed power setting.
6. Variable Power control* - Rotate the On/Off button to increase or decrease the
suction level. Use low suction for delicate fabrics. [8]
7. switch off at the end of use by pressing the On/Off button. Unplug and press the cord
rewind pedal to wind the power cord back into the cleaner. [9]
Parking and Storage - The tube can be parked for temporary storage while in use [10], or
in the storage position when not in use. [11]
*Certain models Only ** may vary according to the model
M. Carpet and Floor nozzle (GP)**
M1. Carpet Nozzle (CA)**
M2. Hard Floor Nozzle (HF)**
N. Floor Type selector Pedal**
O. Exhaust Filter
P. Pre-motor filter
Q. Accessory set
Qa. Crevice Tool
Qb. Furniture Nozzle
R. Parquet Nozzle*
s. Pet Hair Remover Mini Turbo Nozzle*
T. Allergen Remover Mini Turbo Nozzle*

ClEANER mAINTENANCE

Replacing The Dust Bag
If the bag check indicator is red please check and, if necessary, replace the bag.
1. Lift the bag door release latch [12] to open the cover, and pull the bag collar to remove
the bag. [13]
2. Fold a new bag as shown [14] and fit by inserting the collar into the bag holder. [15]
3. Close the bag door.
wARNING - The bag door will NOT close if the dust bag and/or the bag holder are not
assembled to the cleaner. Always ensure the bag and bag holder are present when closing
the bag door.
Remember: The bag check indicator may also be red if an obstruction has occurred. In this
case refer to 'Removing A Blockage From the system'.
Pre-motor and exhaust filter maintenance
1. To maintain optimum performances from your cleaner, please wash the filters after each
5 bag changes.
2. Lift the bag door release latch [12] to open the cover and pull the bag collar to remove
the bag. [13]
3. Remove the pre-motor filter and the exhaust filter from the cleaner. [16, 19]
4. Remove the pre-motor filter from the holder. [17]
5. Rinse both filters under hand warm water. [18, 20]
6. Do not scrub the filters, use washing up liquid or place in a dishwasher.
7. Remove excess water with a dry cloth and leave to air dry for 24 hours or until fully dry.
8. After completing the washing and drying operations, locate the filters in their original
positions in the cleaner.
IMPORTANT - Regularly check and maintain the filters by following the filter
maintenance instructions, it is also recommended that you purchase new filters
after every 3rd filter wash. This will maintain your cleaners performance over time.
Removing a Blockage From The System
If the bag check indicator is illuminated or flashing:
1. Check if the bag is full. If so refer to 'Replacing The Dust Bag'.
2. If it is not full, then:
A. Do the filters need cleaning? If so refer to 'Cleaning the Filter'.
B. Check if there is any other blockage in the system - Use a rod or a stick to remove
any blockage from the Telescopic tube or flexible hose.
wARNING - The bag check indicator will turn red if the cleaner is used when full, if there is a
2
GB