Ryobi PMP01 Manuel D'utilisation page 6

closing completely exposing the battery and the battery port
to moisture, debris, and other contaminants.
 Set pump switch to the OFF ( O ) position.
 Press the tab to open the battery compartment latch.
 Insert the battery pack into the battery port.
 Make sure the latches on each side of the battery pack
snap into place and the battery pack is secured before
beginning operation.
 Close the battery compartment cover and press until it
snaps shut.
MOUNTING THE MISTING KIT
See Figures 3 - 5, page 10.
WARNING:
Install alligator clamps in an area where no electrical
wires, utility cables, pipes, or other obstructions are
located. Never connect alligator clips to electrical wires
or cords. Contact your local utility company or a qualified
electrician if you are unsure. Ensure alligator clamps
and misting tube are securely installed to prevent falling
object or slippery surface hazard. Failure to follow these
instructions can result in electrical shock or other serious
personal injury.
NOTICE:
This misting kit is designed to be attached to fabric
surfaces, such as umbrellas or fabric awnings, using the
included alligator clips. To attach the misting kit to other
surfaces, an accessory hanging mount kit must be used.
To obtain the best spray area (mist curtain), we recommend
the misting tube be secured to an overhead support. Always
mount the misting kit in a suitable location away from electrical
devices and switches.
To mount the misting kit:
 Set pump switch to the OFF (O) position and remove the
battery pack.
 Use the plastic straps on the alligator clamps to secure
the misting tube to the clamps.
 Squeeze the ends of the clamp to open the clamp mouth
and install the misting kit in a suitable location.
USING THE MISTING KIT WITH A WATER
BUCKET (NOT INCLUDED)
See Figures 6 - 8, pages 10 and 11.
WARNING:
Children can fall into buckets and drown. Keep children
away from buckets with even a small amount of liquid.
OPERATION
The misting kit is designed to operate on top of a 5-gallon
water bucket.
NOTE: Clean the bucket with soap and water before each use.
 Place the bucket on a flat, level surface.
 Set the pump switch to the OFF ( O ) position.
 Set the pump's base securely onto the rim of the bucket,
allowing end of the intake tube to go straight down into
the bucket.
NOTE: The pump cannot be secured to the bucket; they
cannot be moved as a single unit.
 Install the battery pack and close the battery compartment
cover.
 Add ONLY clean, cold water into the bucket. Do not
overfill.
 With the misting kit mounted in your desired location,
away from electrical devices and switches, start the
pump, and allow the system to pressurize.
WARNING:
When filling, moving, or emptying bucket, be careful not
to spill water and do not overfill bucket. Spilled water can
result in a slippery surface, create a slip and fall hazard,
and cause property damage.
 After adequate pressure is reached, water should mist
from the nozzles to the surface below. If misting does not
occur within 10 seconds, shut off the pump, and refer to
the Troubleshooting later in this manual.
To move the misting kit to another location:
 Set the pump switch to the OFF ( O ) position.
 Allow the the pump to stop running, then lift the pump
off the bucket and move as desired.
NOTE: The intake tube cannot be removed, but may be
stored in the space provided on the unit.
USING THE MISTING KIT WITH A GARDEN
HOSE (NOT INCLUDED)
See Figure 9, page 11.
WARNING:
Always route hoses away from traffic areas to prevent a
tripping hazard.
NOTE: The pump is not needed when the misting kit is
connected to a garden hose. Using the pump unnecessarily
may cause additional wear and shorten the life of the unit.
 Set the pump base on a flat, steady surface, such as a
concrete patio or tabletop.
6 — English