Safety Instructions; Maintenance And Storage - Hudora 10130 Instructions De Montage Et Mode D'emploi

INSTRUCTIONS ON ASSEMBLy AND USE
EN
CONGRATULATIONS ON PURCHASING yOUR PRODUCT!
Please read these instructions carefully. The instructions are an integral component
of the product. Therefore, please store them and the packaging carefully in case
questions arise in the future. Please always include these instructions when giving the
product to a third party. This product must be assembled by an adult. This product is
not designed for industrial use. The use of the product requires certain capabilities
and skills. Always adjust according to the age of the user and use for the purpose it
has been designed for.
TECHNICAL SPECIFICATIONS
Skate: joey Cruiser walker bike 3.0 12"
Item number: 10130, 10131, 10133, 10134, 10140, 10141
Handlebar height adjustable: from 52.5 - 57.5 cm
Saddle height adjustable from: 35 - 41.5 cm
Maximum carrying capacity: 50 kg
If you have assembly problems or would like further information on the product, we
have all you need and more at http://www.hudora.de/.
CONTENTS
1 x Walker bike:
Front wheel fork
Frame with back wheel
Handlebars
Front wheel
Mudguard for the front wheel
Saddle
Small parts
1 x Usage instructions
Other parts which may be included with the delivery in some circumstances are not
required.

SAFETy INSTRUCTIONS

• This product is only suitable for smooth paved surfaces. Do not use it on public
roads.
• The running bike is only intended for use by one person.
• Warning! Please ensure that your child wears the appropriate protective clothing
(helmet).
• Warning! Driving and stopping can also be done with the application of the foot;
the impeller must therefore be used only with shoes. There is a risk of injury.
• Do not allow your child to ride the running bike at twilight, at night or in poor visi-
bility.
• To prevent putting your child or others in danger, you should not let the running
bike be used on roads or thoroughfares or on slopes or hills. Avoid using it in the
proximity of stairs or open water.
• Inspect the running bike before each use to ensure that all parts are still fixed in
place correctly and that the running bike is functioning as intended.
• The product has been tested in accordance with standard EN 71. For children
from 2 to 5 years of age only.
• This product contains small parts which could cause asphyxia if swallowed. Su-
pervise children during the assembling. This product must be assembled by an
adult. Children should only use the product when they are under adult supervision.
• Please ensure that your child keeps both hands securely on the handlebars in or-
der to maintain better control over the bike.
• The use of the product requires specific skills and knowledge to be able to avoid
injuries due to crashes and collisions.
• Warnings! Protective equipment should be worn (helmet). Not to be used in traffic.
50 kg max.
All images are examples of the design.
ASSEMBLy INSTRUCTIONS (DIAGRAM 1 - 6)
1. Attach the mudguard for the front wheel to the front fork using a screw, washer
and nut. The mudguard for the back wheel is pre-mounted.
2. Put the front wheel into the fork and tighten thenuts. Make sure the hooks in the
lock washers are in their intended holes in the fork.
3. Push the fork from below through the frame, as shown in the diagram 3. Make sure
there is a plastic disc above and below the frame shaft.
4. Push the covering cap over the handlebar shaft. Then push the handlebar clamp
onto the fork shaft from above. Make sure that the handle clamp fits exactly onto
the fork shaft and is pushed down as far as possible. Check that the rings and the
guide sleeves are fully fitted into the frame. Now insert the handlebars into the fork
shaft from above. In order to set the handlebars at the highest position, pull out the
vertical handlebar shaft to any further, as this may lead to accidents. Make sure
that the handlebar shaft is fixed in correct alignment with the front wheel before
screwing the handlebars tightly into place.
5. Push the covering cap over the handlebar clamp.
6. Insert the saddle into the seat post. Make sure that the maximum seat height is not
exceeded, i.e. do not pull the seat post out beyond the MAX marking, as exceeding
the maximum seat height may lead to serious injury.
SETTING UP THE BAND BRAKE (DIAGRAM 7)
The brake system is pre-mounted in the factory and should be checked and adjusted
if needed before the bicycle is put into use. If you find the brake action insufficient
when checking the brakes, please turn the adjusting screw (a) a few times outwards
and the brake pressure will increase. If required, the brake cable on the screw (b) can
be set tighter by unscrewing the clamping nut and retightening the cable. Then tight-
en the clamping nut again. If this should still not suffice, you can adjust the brake
pressure by adjusting both brake drum screws (c) in quarter turns. After each adjust-
ment, check that the wheel can move freely as otherwise the brakes could get dam-
aged.
IMPORTANT!
After doing any work on the brakes please always check carefully to ensure that all
screws have been tightened and are functioning correctly.

MAINTENANCE AND STORAGE

Use a dry or damp cloth only to clean the product; do not use special cleaning agents!
Check the product for damage or traces of wear and tear before and after each use.
Do not make any structural changes. For your own safety, please use original spare
parts only. These can be sourced from HUDORA. If parts become damaged or if sharp
edges or corners should develop, the product may not be used any more. If in any
doubt, please contact our service team (http://www.hudora.de/service/). Store the
product in a safe place where it is protected from the elements, cannot be damaged,
and cannot injure anyone.
This product may only be inflated by an adult. Inflate it with your foot, a hand pump or
a low-pressure pump to max. 30 psi (~ 2 bar). Do not use high-pressure compressors.
Close the valve cap tightly so that the child cannot open it by himself!
DISPOSAL ADvICE
At the end of the product's life, please dispose of it at an appropriate collection point
in your area. Local waste management companies will be able to answer your que-
stions on this.
SERvICE
We make every effort to deliver faultless products. If faults do arise however, we put
just as much effort into rectifying them. Therefore, you can find numerous information
on the product, replacement parts, solutions to problems and lost assembly manuals
at http://www.hudora.de/service.
HUDORA I Jägerwald 13 I 42897 Remscheid I Germany
www.hudora.de
Item no. 10130, 10131, 10133,
10134, 10140, 10141
As of 01/12
Page 4/8